voirbosed heat englieibleA solag enentich ocecieves 80 KT of heat andorejets 70kJ of hcat fo the ambientat 30'c isto be designed The thesumalefficiency of the heatheenorgyirsofengine

Given data; Solar energy based het engine which recieves Q1=80kJQ2=70kJT2=300C=30+273=303…

Answered: f the heat engl

Engineering

Mechanical Engineering

f the heat engl

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.21P

See similar textbooks

Similar questions

Ball bearing ro=4 mm leaving the oven at a uniform temperature of 900 oC are exposed to air for a while before they are dropped in to the water for quenching . Determine the time they can stand the air before their temperature falls below 850 oC also find the total rate of heat transfer .Take for the balls k = 54 W/m .oC , ρ= 7833 kg/m3 , Cp=0.456 kJ/kg.oC
a container with an internal volume of 2.94 m³ is occupied by ten steam at 0.88 mpa with an internal energy energy of 27, 956.0 kj .Determine a) its temperature b. total entalphy ,kj
A steel billet of 2000 kg mass is to be coolec from 1250 K to 450 K. The heat released during this process is to be used as a source of energy. The ambient temperature is 303 K and specific heat of steel is 0.5 kJ/kgK. The available energy of this billet is?
A glass container with an insulationg cover with a surface areaof (r+150) cm2 and (r+10) mm tick is filled with ice at 0 c and placed in a second vessel maintained at atemperature of (r+80)c. find the mass of the ice that melts per minute when the flow of heat becomes steady specific latent heat of ice=3.36*105 J/KG and k for glass is 1w /mk
The motor of an electrical appliance consumes 18 000 J. during itsoperation, 9450 J dissipated in heat, 250 J were used forproduce light and 350 J are required to power the electronic panel ofdevice. What is the fuel efficiency of the engine of this device ?
Heat is being generated within a 6 m long stainless steel cylinder with the amount of 2kW. The thermalconductivity of the cylinder is constant at 15.1 W/moC. The temperature and the heat transfercoefficient of the environment are 30oC and 140 W/m2 respectively and the heat is transferred insteady state. Determine the cylinder surface temperature a) by using the applicable relation, and b)by using differential equation and solving it.
Consider the heating of water in a pan on a top of a range. If 24 kJ of heat is transferred to the water from heating element and 6 kJ of it is lost from the water to the surrounding air. Determine;(a) the net heat transfer to the water,(b) the efficiency for boiling water.
In an annealing process, a 50-mm-thick stainless steelplate (r = 8238 kg/m3, cp = 468 J/kg·K, k = 13.4 W/m·K,and a = 3.48 * 10–6 m2/s) was reheated in a furnace from aninitial uniform temperature of 230°C. The ambient temperatureinside the furnace is at a uniform temperature of 1000°Cand has a convection heat transfer coefficient of 215 W/m2·K.If the entire stainless steel plate is to be heated to at least600°C, determine the time that the plate should be heated inthe furnace using (b) the Heisler char.
A coal with a higher heating value of 6,700 Kcal/kg is consumed at a rate of 600 kg/hr. in a water tube steam generator with a rated boiler horsepower of 200 HP. The feedwater temperature is 82°C and steam generated is at 11 kg/cm2 absolute, saturated. The developed boiler horsepower is equivalent to 305 HP. Determine: a. Heating surface area in m²b. Steam evaporated in kg/hrc. ASME evaporating units in J/hrd. Percent ratinge. Factor of evaporationf. Over-all thermal efficiencyg. actual specific evaporationh. Equivalent specific evaporation
Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1631 kJ is supplied to saline water in the steam generator to heat from 23ºC to 115ºC for the generation of water vapor, Take the density & specific heat of the solution as 1010 kg/m3 & 3.8 J/kgºK respectively. Solution: Change in Temperature (in K) Mass of the saltwater (in kg) Quantity (Volume) of saltwater (in m3)
An air cooled condenser is to reject 70 KW of heat from a condensingrefrigerant to air. The condenser has an air side area of 210 m2 and a Uvalue based on this area of 0.037 KW/m2-K; it supplied with 6.6 m3/s of airwhich has a density of 1.15 kg/m3. If the condensing temperature is to belimited to 55°C, what is the maximum allowable temperature of the inletair? (°C)
It has been suggested that a heat engine could be developedthat made use of the temperature difference between waterat the surface of the ocean and water several hundredmeters deep. In the tropics, the temperatures may be 27°Cand 4°C, respectively. (a) What is the maximum efficiencysuch an engine could have? (b) Why might such an enginebe feasible in spite of the low efficiency? (c) Can you imagineany adverse environmental effects that might occur?