F tonnes/hr Separation size required is -2 inch C tonnes/hr U tonnes/hr If the feed flow rate is 300 t/h and the feed contains 35% of undersize. Calculate: 1) Mass of undersize fraction in the feed; 2) The mass of oversize fraction in the feed 3) The screen efficiency if the undersize fraction contains 90% of - 2 inch while the oversize fraction contains 95% of +2 inch.

F tonnes/hr Separation size required is -2 inch C tonnes/hr U tonnes/hr If the feed flow rate is 300 t/h and the feed contains 35% of undersize. Calculate: 1) Mass of undersize fraction in the feed; 2) The mass of oversize fraction in the feed 3) The screen efficiency if the undersize fraction contains 90% of - 2 inch while the oversize fraction contains 95% of +2 inch.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please typing answer only IENG 302 - Manufacturing Processes: We are reducing the diameter of a 95.8 mm cylinder to 30.04 mm using 7 roughing passes and 3 finishing passes. The finishing operations use a depth of cut of 1.51 mm. The roughing operations are performed with a feed rate of 9.61 mm/s and the finishing operation is performed with a feed rate of 11.31 mm/s. a) What is the depth of cut for a roughing pass? b) What is the rate of material removal (mm^3/s) for the third roughing pass? c) What is the rate of material removal (mm^3/s) for the final finishing pass? d) What is the average rate of material removal (mm^3/s) for the roughing operations?
9.738 seems correct. Please show your work as fast as
(USCS units) A turning operation is performed using a rake angle of 15°. Cutting speed = 200 ft/min, feed= 0.012 in/rev, and depth of cut = 0.100 in. The chip thickness ratio measured after the cut = 0.48. Determine (a) chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain (USCS units) The turning operation in the previous problem involves a work material whose shear strength = 52,000 lb/in2. Based on your answers to the previous problem, compute (a) shear force, (b) cutting force, (c) thrust force, and (d) friction force.
The following data is given for slab milling of a 300 mm long 50 mm wide mild steel block: Cutter of diameter= 60 mm; Numbers of teeth =12; Cutter speed = 120 rev/min; Depth of cut = 3.2 mm; Feed is 0.25 mm/tooth.Determine (i) Table feed in mm/min, (ii) MRR (iii) Power (iv) Torque and (v) Total machining time. Assumesuitable approach and over-run and specific energy of mild steel as 5 Ws/mm3.
7. Show the step-by-step process. Do not use shortcut methods. Make it as detailed as it can be.
The break-even Revenue (at no profit) of a mine is $70M per tonne of ore. It costs $46M per tonne of ore to produce the ore mineral and it costs $3M per tonne of waste to extract and handle the waste. (i) Calculate the BESR. (il)) What would be the profit/lass per tonne of ore, if the mine management decided to change (reduce or increase) the stripping ratio to 3.1?
A part to be turned in an engine lathe must have asurface finish of 1.6 mm. The part is made of a freemachining aluminum alloy. Cutting speed = 150 m/min,and depth of cut = 4.0 mm. The nose radius on the tool =0.75 mm. Determine the feed that will achieve thespecified surface finish.
A slab milling operation is performed on the top surface of a tool-steel workpiece 450 mm long by 7.5 cm wide. The helical milling cutter, which has an 80 mm diameter and seven teeth, is set up to overhang the width of the part on both sides. Cutting speed is 4000 mm/min, feed is 0.015 cm/tooth, and depth of cut = 0.60 cm. Determine (a) the actual machining time to make one pass across the surface and (b) the maximum metal removal rate during the cut. (c) If an additional approach distance of 0.05 m is added at the beginning of the pass, and an overtravel distance at the end of the pass equal to the cutter radius plus 0.0115 cm, what is the duration of the feed motion
A cemented carbide tool is used to turn a part with length = 18.0 in and diameter = 3.0 in. The parameters in the Taylor equation are: n = 0.27 and C = 1200. The rate for the operator and machine tool = $33.00/hr, and the tooling cost per cutting edge = $2.00. It takes 3.0 min to load and unload the workpart and 1.50 min to change tools. The feed = 0.013 in/rev. Determine: Cutting speed for maximum production rate, Tool life in min of cutting, and Cycle time and cost per unit of product.
Excavator loading time = 36 seconds per loading pass Truck travelling time = 351 seconds per truck Truck dumping time = 22 seconds per truck Unloaded truck Travelling back time = 181 seconds per truck Truck queuing or waiting time = 75 seconds/truck Excavator-truck spotting time = 14 seconds/truck Estimate the total number of units (trucks), if the total production of a coal mine is 4Mt per year at 91% recovery. Use the cycles per production hour from above, figure out with your reasonable detailed calculations and assumptions for all other parameters you need in your calculations including the loose and bank (prime) volume and tonnage of the coal per truck per year.
In a turning operation, cutting speed =200 m/min; feed = 0.25mm mm/rev, and depth of cut = 4.00mm Thermal diffusivity of the work material = 20m mm^2/s and volumetric specific heat =3.5(10^ -3 )J/mm^ 3 -C If the temperature increase above ambient temperature (20degreesC) is the angle measured by a tool-chip thermocouple to be 700degreesC, determine the specific energy for the work material in this operation.
We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical milling machine and 50 cm from the edge. The width of the slot is 40 mm. TheDepth of the slot is 25 mm. For this, several rough cutting steps and aFine cut with a depth of 0.20 mm. The depth for each of the steps ofrough cut is limited to 1.75 mmAditional information:What is the number of blades used for the rough cutting steps?What is the number of blades used for the fine cutting step?