Q1/ A cuber of the type of open-end đies arranged in a ring, has 66 dies, each 32x32x150 mm. a-Calculate the time required for a given particle of hay to pass through the die when the feed rate is 5.5 Mg\h. Assume an individual-cube density of 800 kg\m. b-If the cube length averages 55 mm, how much energy per cube is requited for the actual cubing operation, if the cubing energy required was 12 kw.h\Mg.

Q1/ A cuber of the type of open-end đies arranged in a ring, has 66 dies, each 32x32x150 mm. a-Calculate the time required for a given particle of hay to pass through the die when the feed rate is 5.5 Mg\h. Assume an individual-cube density of 800 kg\m. b-If the cube length averages 55 mm, how much energy per cube is requited for the actual cubing operation, if the cubing energy required was 12 kw.h\Mg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The friction in direct extrusion is ________ Indirect extrusion. a) Greater than. b) Equal to. c) Less than.2. The Temperature in hot forming process is ____. a) (0 to 0.4) Tm. b) (0.5 to 0.75) Tm. c) 0.9 Tm. d) 0.4 Tm. e) 0.8 Tm. f) (0.3 to 0.5) Tm. Where Tm is the melting temperature of the work piece.3. Maximum draft in rolling depends on _______. a) Coefficient of friction and roll radius. b) Thickness of plate. c) Smoothness of roll Surface. d) Roll rotational speed.e) Width of the plate. f) Length of the plate.4. In deep drawing process, the drawing ratio (DR) has a higher limit (value) of:- a) 6. b) 1. c) 4. d) 5. e) 7. f) 2. g) Zero.5. Spring Back is a phenomena usually associated with which of the following processes:-a) Extrusion. b) Forging. c) Bending. d) Wire drawing. e) Rolling. f) Sheet metal cutting. g) Deep Drawing.
A compound die will be used to blank and punch a large washer out of 6061ST aluminum alloy sheet stock 3.50 mm thick. The outside diameter of the washer is 50.0 mm and the inside diameter is 15.0 mm. Determine (a) the punch and die sizes for the blanking operation, and (b) the punch and die sizes for the punching operation Vallue for allowance = 0.060
the work metal has a flow curve defined by K=300MPa and n=0.2, and the coefficient of friction between the rolls and the work is assumed to be 0.1. a 250mm wide strip 2.0cm thick is fed through a rolling mill with two powered rolls each of radius=300mm. the work thickness is to be reduced to 18mm in one pass at a roll speed of 50rev/min. what will be the power for this operation?
In a sheet metal forming press, the shape to be formed is hemispherical cup of radius 15 cm in 2mm thick mild steel sheet. The force required to deform sheet is 8 kN. The forming hammer should approach job from a distance of 30 cm. The production rate required is 240 components/hr. Calculate and suggest the following specifications of the various hydraulic components used: a. Hydraulic cylinder (bore & length); b. Pump pressure and flow rate; c. Electric motor HP considering 75% pump efficiency; d. Reservoir size; and e. Size of pump inlet and discharge tubing.
In a slab rolling operation, the maximum thickness reduction (del hmax) is given by del hmax = μ²R, where R is the radius of the roll and u is the coefficient of friction between the roll and the sheet. If µ = 0.1, find the maximum angle subtended by the deformation zone at the centre of the roll.
In a single pass rolling process using 412mm diameter steel rollers, strip of width 120mm and thickness 8mm undergoes 10%reduction of thickness. The angle of bite in radians is.
A solid cylinder of diameter 100 mm and height 50 mm is forged between two frictionless flat dies to a height of 25 mm The percentage change in diameter is... (a) 0 (b) 2.07 (c) 20.7 (d) 41.4
Von mises and tresca agree in pure shear
Manufacturer process A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength = 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking. Take: Ac=0.06
A sheet 300mm wide 25mm thick with two drives, each with a radius of 250mmit is passed through a rolling stand with rollers. Work is thickness in one layer at 50 rpm roll speed 22reduced to mm. The work material has a yield curve determined by K = 275 MPa and n = 0.15.The friction coefficient between the rollers and the work is considered to be 0.12. Successful rolling of frictionDetermine if it is sufficient to allow its operation. If it is sufficient;a) Rolling force,b) Momentc) Calculate the power.
q1)Work-parts that have low area to- volume ratio are called. Select one: a. Bulk b. Billets c. Sheet metals d. Foils e. Plates q2)A 42.0-mm-thick plate made of low carbon steel is to be reduced to 34.0 mm in one pass in a rolling operation. As the thickness is reduced, the plate widens by 4%. The yield strength of the steel plate is 174 MPa and the tensile strength is 290 MPa. The entrance speed of the plate is 15.0 m/min. The roll radius is 325 mm and the rotational speed is 49.0 rev/min. Determine (a) the minimum required coefficient of friction that would make this rolling operation possible?
The maximum possible draft in rolling which is the difference between initial and final thickness of the sheet metal, depends on A. Rolling force B. Roll radius C. Roll width D. Yield shear stress of the material