need correct an urgent Fig. 3 shows the load torque variation for one cycle of a shaft driven by a constant torque.With an appropriate value of speed, determine the cross-section of the rim when the rim istwice the thickness and the total speed fluctuation not to exceed 0.2. Assume density of rimas 8050 kg/m and Imachine is 125 kgm?.Torque (Nm)1000800e (rad)- 350Fig. 3

Here given we have b=2tCs=0.2δ=8050 kg/m3I=125 kgm2Cycle time =4π

Fig. 3 shows the load torque variation for one cycle of a shaft driven by a constant torque With an appropriate value of speed, determine the cross-section of the rim when the rim twice the thickness and the total speed fluctuation not to exceed 0.2. Assume density of r as 8050 kg/m³ and Imachine is 125 kgm?. Torque (Nm) 1000 800 O (rad) 47 -350

Fig. 3 shows the load torque variation for one cycle of a shaft driven by a constant torque With an appropriate value of speed, determine the cross-section of the rim when the rim twice the thickness and the total speed fluctuation not to exceed 0.2. Assume density of r as 8050 kg/m³ and Imachine is 125 kgm?. Torque (Nm) 1000 800 O (rad) 47 -350

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. ) power tranmission = 270 kw (1) speed 65 rpm, () Maximum shear stress = 55 MPa (iv) diameter ratio = 1.78 (v) The maximum value of the twisting moment is 40% greater than its mean. Find, (i)The mean torque is (Unit is in Nm)=, (ii)The maximum torque is (Unit is in Nm)=. (iii) The outer diameter of the shaft (unit in mm) (iv) The inner diameter of the shaft (unit in mm)
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 290 kW(ii) speed = 60 rpm,(iii) Maximum shear stress = 65 MPa(iv) diameter ratio = 1.5(v) The maximum value of the twisting moment is 40% greater than its mean. The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
A solid steel shaft, whose Sy= 300 MPa and Su= 400 MPa, is used to transmit 3000 kW at 800 rpm. Determine its diameter.
Consider a double hook, thaving intermediate shaft of moment of inertia 3 g-m², the input and output shaft of which are in clined at 30° to intermediate shaft. The input shaft rotates uniformly at 2400 rpm with steady torque of 300 N.m., determine max. fluctuation in output torque.
The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in diameter and shear modulus G of 80,000 MPa is:
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) Power transmission =60 kW,(ii) Shaft speed = 160 rpm,(iii)The angle of twist / m length = 1.1º(iv)Maximum twisting moment is 30% greater than its mean. (v) Take Modulus of rigidity as 105 Gpa. (i) Mean torque of the shaft (unit in Nm) = (ii)Maximum torque of shaft (unit in Nm) = (iii) The diameter of the shaft (unit in mm) = iv) Maximum shear stress in the shaft (Unit in MPa) is
A multi-cylinder engine is to run at a speed of 600 r.p.m. On drawing the crank-effort diagram to scale of 1 cm 2452.5 N-m and I cm 30°, the areas above and below the mean torque line in sq.cm. are as follows: +1.6, -1.72, +1.68, -1.91, +1.97 and -1.62. The speed is to be kept within ±1% of the mean speed of the engine. Calculate the necessary moment of inertia of the flywheel. Determine the suitable dimensions of a rectangular flywheel rim, if the breadth is twice the thickness. The density of the cost- iron is 725 gm/cm' and its hoop stress is 588.6 N/cm2. Assume that the rim contributes 92% of the flywheel effect.
The rotation in degrees of a shaft, 800 mm long subjected to atorque of 80 N-m, 10 mm in radius and shear modulus of 85 GPais
An engine shaft running at 1,748 r.p.m. is required to drive a machine shaft by means of a belt. The pulley on the engine shaft is of 3 m diameter and that of the machine shaft is 6 m diameter. Determine the speed of the machine shaft, when there is a slip of 2%.
Write legibly, provide manual step by step solution, and diagram for below given problem. A 50cm diameter solid shaft is desired to replace a hollow shaft havng 75cm outside diamter. Consider the strength to be the same, determine the inside diameter of the hollow shaft. Ans. 68.69cm
2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 230 kW(ii) speed = 80 rpm,(iii) Maximum shear stress = 60 MPa(iv) diameter ratio = 1.74(v) The maximum value of the twisting moment is 40% greater than its mean. (i) The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
. A 102 mm diameter shaft is driven at 3000 rpm by a 250 Hp motor.The shaft drives a 121.9 cm diameter chain sprocket. Compute thetorque in kN.m