Figure 1 shows the Ward-Leonard method of speed control. i. Explain in your own words how the circuit operate. the counterede.m.f. ii. Briefly explain what happens to the speed of the motor if the generated voltage ES is less than iii State two (2) advantages of the Ward-Leonard method of speed control when compared with other methods of controls

Figure 1 shows the Ward-Leonard method of speed control. i. Explain in your own words how the circuit operate. the counterede.m.f. ii. Briefly explain what happens to the speed of the motor if the generated voltage ES is less than iii State two (2) advantages of the Ward-Leonard method of speed control when compared with other methods of controls

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.24P: For Problem 3.18, the motor operates at full load, at 0.8 power factor leading, and at a terminal...

See similar textbooks

Similar questions

The following information is given for a 300 kw, 600 V long shunt compound generator. Shunt field resistance = 75 Ω, armature resistance including brush resistance = 0.03 Ω, commutating field winding resistance = 0.011 Ω, series field resistance = 0.012 Ω, diverter resistance = 0.036 Ω. When the machine is delivering full load, calculate the voltage, power generated by the armature and efficiency.
If the armature resistance of a 3-phase, 318.75 kVA, 2300-V synchronous generator is 0.35 ohms per phase, the synchronous reactance is It is 1.2 ohms. Calculate the excitation voltage and voltage regulation for the following load cases: a) Full load, back power factor of 0.8 and rated voltage. b) Full load, forward power factor of 0.6 and rated voltage.
A 1500KVA, 11KV, 50Hz, Star connected synchronous generator is tested by operating it as a synchronous motor on no-load. The results are as follows: When operated as a synchronous motor on load the power input to the motor is 55.8KW and the armature line current is 70A. The excitation of 38.6A at 250V dc gives the normal open-circuit voltage. DC resistance test: dc line voltage 17.5V and dc line current 70A. Take the effective resistance as 1.6 times the dc resistance. Calculate the efficiency of the machine on 80% of the full-load and 0.75 power factor lagging
The synchronous reactance of a generator is 1.0 per unit, and the leakage reactance of itsarmature is 0.1 per unit. The voltage to neutral of phase a at the bus of a large system to which the generator is connected is 1.0∠0 ◦ per unit, and the generator is delivering a current Ia = 1.0∠− 30◦ per unit. Neglect resistance of the winding and find:a. the voltage drop in the machine due to armature reactionb. the internal voltage to neutral E of phase a of the generatorc. the per unit values of P and Q delivered to the bus Note: Equivalent circuit is shown in Fig. 1 where Xar armature reactance, Xl leakagereactance, and XS synchronous reactance
4. A 6 pole wave wound shunt generator delivers 200A at a terminal voltage of 240V. Ra and Rsh are 0.03Ω and 70Ω respectively. Neglecting brush drop, determine (i) armature current (ii) current per parallel path (iii) generated voltage and (iv) Power developed. armature current ? current per parallel path ? generated voltage ? Power developed ?
For Problem 3.18, the motor operates at full load, at 0.8 power factor leading, and at a terminal voltage of 10.45 kV. Determine (a) the voltage at bus 1, which is the generator bus, and (b) the generator and motor internal EMFs.
For the starting method given in task 8, redraw each of the symbols used in the control circuit and give a brief explanation of their purpose. Task 8 below (Task 8 has been answered already) (There are many methods used for starting induction motors and synchronous machines. For the following three methods of starting three-phase motors, explain how the starting method works and state the type of motor the starter is designed for. Support your answer with illustrations: Star-Delta Rotor Resistance Induction starting (with damper windings).)
1-) a) Does the slip increase as the load increases in an asynchronous motor? Explain what is the reason for this. b) What does it mean when the slip is 0, 1, -1 in asynchronous motor, how is it achieved? Explain.
1. What is the use of a synchronous motor in a power system network? Explain in detail with a diagram.(350words)
Three phase induction motor Leakage Reactance five times Resistance for stator and rotor and impedance for stator and rotor is equal. Slip at full load is 0.02 .calculate the resistance that added for starting current equal three times full load current, Calculate starting torque in this case. if the slip ring is short circuited calculate the ratio of starting current in two cases ..no. of poles is 4 and frequency is 50 Hz
In plugging type of braking system of DC motor, the current in the series and shunt fields must not be reversed" True False
a) Does the slip increase as the load increases in an asynchronous motor? What is the reason of this? b) What does it mean for Slip 0, 1, -1 in asynchronous motor, how is it achieved? Explain.