Figure A -L- Figure B FL + D- P. -> In the figure, two identical springs have unstretched lengths of 0.26 m and spring constants of 310 N/m. The springs are attached to a small cube and stretched to a length L of 0.32 m as in Figure A. An external force P pulls the cube a distance D = 0.039 m to the right and holds it there. (See Figure B.) The work done by the external force P in pulling the cube 0.039 m is closest to W = J J (2 decimal places)

Figure A -L- Figure B FL + D- P. -> In the figure, two identical springs have unstretched lengths of 0.26 m and spring constants of 310 N/m. The springs are attached to a small cube and stretched to a length L of 0.32 m as in Figure A. An external force P pulls the cube a distance D = 0.039 m to the right and holds it there. (See Figure B.) The work done by the external force P in pulling the cube 0.039 m is closest to W = J J (2 decimal places)

Name: Figure A->Figure BEL +D->PР.In the figure, two identical springs have
Uploaded: 2024-03-20T06:58:04.000Z
Channel: Bartleby
Description: Figure A->Figure BEL +D->PР.In the figure, two identical springs haveunstretched lengths of 0.26 m and springconstants of 310 N/m. The springs areattached to a small cube and stretched to alength L of 0.32 m as in Figure A. An externalforce P pulls

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter7: Conservation Of Energy

Section: Chapter Questions

Problem 83P

See similar textbooks

Similar questions

Check Your Understanding Identify an object that undergoes uniform circular motion. Describe how you could trace the SHM of this object.
An 1150kg automobile has springs with k = 16,000N/m. One of the tires is not properly balanced; it has a little extra mass on one side compared to the other, causing the car to shake at certain speeds. If the tire radius is 42cm, at what speed will the wheel shake most? [Sketch the scenario first]
You pull a simple pendulum 1.40 m long to the side through a small angle of 3.50º. What is the speed of the pendulum as it passes through equilibrium? Give your answer in m/s.
To measure the static friction coefficient between a 1.40-kg block and a vertical wall, a spring (k = 770 N/m) is attached to the block, is pushed on the end in a direction perpendicular to the wall until the block does not slip downward (see figure). If the spring is compressed by 0.048 m, what is the coefficient of static friction?
A spring (k888 N/m) is hanging from the ceiling of an elevator, and a 7.1 kg object is attached to the lower end. By how much does the spring stretch (relative to its unstrained length) when the elevator is accelerating upward at a 0.74 m/s²?
https://www.youtube.com/watch?v=6F6deDoKLoE During the lab, you fire the ballistic pendulum multiple times and find the average angle to be 46.7 degrees. If the length of the pendulum (from pivot to center of gravity) is 30.4 cm, to what height, h, did the pendulum's center of gravity rise? (Use the formula shown at 7:45 of the video) Give your answer in cm to 3 significant figures (2 decimal places in this case).
Some old clocks were powered by coil springs that gradually lost torque asthey unwound. A “fusee” was used to compensate for the gradual loss of torque, allowing more accurate timekeeping. The fusee is a cone-shaped pulley with a helical groove around it, wound with a cord or chain which is attached to the mainspring. Suppose the spring develops a torque of Ts = kθ, where the torsional stiffness k = 0.02 Nm/rad and θ is the angle of twist of the spring in radians. When θ = 4 rad, the cord acts on the part of the fusee with a radius of 10 mm. If the fusee provides constant torque for all θ, what should the radius be when θ = 3 rad?
Answer the question in full details, thank you very much: A thin uniform rod has mass M = 0.310 kg and length L = 0.470 m. It has a pivot at one end and is at rest on a compressed spring as shown in (A). The sequence below shows that the rod is released from an angle 1 = 65.0 degrees, and moves through its horizontal position at (B) and up to (C) where it stops with Angle 2 = 105 degrees, and then falls back down. Assume friction at the pivot is negligible. Calculate the (translational) speed of the center of mass (CM) at (B) in m/s. The spring in (A) has a length of 0.118 m and at (B) a length of 0.148 m. Calculate the spring constant k in N/m.
This time the pendulum is 1.04 m long. Suppose you start with the pendulum hanging vertically, at rest. You then give it a push so that it starts swinging with a speed of 1.29 m/s. What maximum angle (in degrees) will it reach, with respect to the vertical, before falling back down?
A spring with a spring constant of ? = 15 ?/?has vertically from the ceiling. You attach a 2kg weight to the bottom of the spring. How far from its equilibrium position has the bottom of the spring stretched?
How much force is needed to stretch a spring 320cm from its equilibrium position? (k = 48 N/m) Please the handwriting, make sure the answer is readable and i can understand thank you;!
A 500 g mass is attached to the end of an initially unstretched vertical spring for which k=30N/m. The mass is then released, so that it falls and stretches the spring. How far will it wall before stopping after SHM? what is the total energy?