Figure Q1 below shows a gear reducer unit which drive a cement mixer drum at output of this unit and attached to a motor at the input. A 1.5 kW motor with a speed of 9 33 rpm is used as an input source to drive this gear reducer. The gear reducer consists two pairs of spur gears which each pair of them have modules of 1.5 mm for gear set 1 and 2.5 mm for gear set 2. All the spur gears have 20 deg pressure angle.

Figure Q1 below shows a gear reducer unit which drive a cement mixer drum at output of this unit and attached to a motor at the input. A 1.5 kW motor with a speed of 9 33 rpm is used as an input source to drive this gear reducer. The gear reducer consists two pairs of spur gears which each pair of them have modules of 1.5 mm for gear set 1 and 2.5 mm for gear set 2. All the spur gears have 20 deg pressure angle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The torque on shaft D is most likely: 2015 lb in 105 lb in 250 lb in 630 lb in
The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The expected rotational speed on shaft E is most likely: 375 rpm 600 rpm 1250 rpm 3000 rpm
Two involute gears of 20-degree pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is 2. If the pitch expressed in module is 5mm and the pitch line speed is 1.2m/s, assuming addendum as standard and equal to one module. Find a.) The angle turned through by pinion when one pair of teeth is in mesh and b.) The maximum velocity of sliding.
Two identical involute, spur gears are in mesh. The module is 4 mm and each gear has 22 teeth If the operating pressure angle is 20° The minimum value of addendum needed to ensure continuous transmission of motion is
Find the diameter of each gear using one simple gear train with 4 gears that work as a speed reducer with a ratio of 5:1 Input of 100 rpm, Output of 20 rpm. Consider number of teeth as: N1=20 N2=40 N3=80 N4=100 Use module of 2
The client requires a single step-up spur gearbox to transmit a 10 kW power from a shaft rotating at 1000 rpm, while the output speed must be 1700 rpm. The material for gear and pinion is 817M40 and 655M13, respectively. Use table 6.10 on page 128 to select the suitable gear and pinion
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
Examine the gear drive shown. The small driving gear has 15 teeth, DP = 8, RPM = 1200, Torque = 4 ft-lbs. The large gear has 54 teeth and DP = 8. What is the Gear Ratio for this system? What is the Speed Ratio for this system? What is the Center to Center spacing of the gears? What is the RPM of the larger gear? What is the Torque supplied by the larger gear?
A pair of spur gear fitted on a motor shaft of lathe machine transmits the power of 7 kW at 600 rpm which is input at pinion gear and its shaft rotates in the counter-clockwise direction. The number of teeth on the pinion and the gear are 22 and 72 respectively, while the module is 8 mm. Assume a pressure angle of 200. Calculate: i) Torque on the shaft of the pinion in Nm. ii) Torque on the shaft of the gear in Nm. iii) Gear ratio iv) Center distance between shafts in mm
mechanical principles Determine the velocity ratio for compound gear systems and the holdingtorque required to securely mount a gearbox.
A pinion shaft of a machine transmits a torque of 68 Nm to the shaft of gear at a speed of 574 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 38 and 78 respectively, while the module is 6 mm. Assume a pressure angle of 200. Calculate: i) Power transmitted by the shaft of the pinion in W. ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in N
Design A two stage spur gear reduction unit with 20- Deg full depth involute teeth. The input shaft rotates at 1440 rpm and receives 10 kW power. The speed of the output shaft should be approximately 180 rpm plus minus 5 rpm , All gears are made of steel and have the same module . Determine appropriate number of teeth of the gears in the unit .