Figure shows an example of pressure vessel with radius of r, and yield stress ??. Suppose the vessel is subjected to uniform internal pressure p, determine the minimum thickness to sustain the pressure according to: (i) Von Mises yield criterion (ii) Tresca yield criterion

Figure shows an example of pressure vessel with radius of r, and yield stress ??. Suppose the vessel is subjected to uniform internal pressure p, determine the minimum thickness to sustain the pressure according to: (i) Von Mises yield criterion (ii) Tresca yield criterion

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.3P: A large spherical tank (see figure) contains gas at a pressure of 420 psi. The tank is 45 ft in...

See similar textbooks

Related questions

Q: Figure 6(a) shows an example of pressure vessel with radius ofr, and yield stress O. Suppose the…

A: Calculated the minimum thickness to sustain the pressure vessel according to the von mises yield…

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

Q: e minimum permissible thickness t min of the tank.

Q: Q2: rotor blade in a mixer. As a consequences, the shaft is suffered a compressive load of P =122 KN…

A: P = 122 KN T = 3.4 KNm Yield stress = 480 Mpa Diameter = 50 mm

Q: A scuba tank is being designed for an internal pressure of 1600 psi with a factor of safety of 2.0…

Q: An cylinder is 30 cm in diameter and the steam pressure is 7 kg/cm. If the cylinder head is held by…

Q: Consider a hollow steel shaft with a 130mm outside diameter and a 70mm inside diameter. What is the…

A: Given Data⇒ Hollow steel shaft Outside diameter of shaft(D)=130 mm=0.13 m Inside diameter of…

Q: For a biaxial stress system consisting of fx=400 MPa(c), fy=175 MPa(t), fs=100 MPa, calculate…

A: To obtain the stresses at a plane which is 35 degree inclined to the x face, the given below…

Q: For a rigid cylindrical steel rod of 2m length 2 cm diameter and yield stress fy = 470 MPa,…

A: Given datalength=2mdiameter= 2 cmyeild stress fy=470 MpaTo determine axial force to yield the rod

Q: Q5) Triaxial undrained test were performed on clay samples taken from clay stratum shown below, the…

A: The Answer is below

Q: Example 133: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm,…

A: The pressure vessel are subjected to high internal pressure, and are designed such a way so that…

Q: A copper cylinder 150mm outside diameter has walls 25mm thick. End plates are stayed by a 25mm…

Q: (a) Figure Q6(a) shows an example of pressure vessel with radius of r, and yield stress Oy. Suppose…

A: For solution refer below images.

Q: Yielding starts in a material when the princip stresses are 100 MPa, 100 MPa and 200 MPa. F per the…

Q: Example 101: A hollow steel tube with an inside Diameter of 100 mm must camy a tensile load of 400…

A: Given data Inside diameter (di) = 100 mm Tensile load (P) = 400 KN Allowable stress = 120 MN/m2

Q: A mild steel shaft of 40 mm diameter is subjected to a bending moment of 115 N-m and torque, T. If…

Q: A steel circular bar (the yield stress ? = 350 MPa) with diameter ? =60mm is acted…

Q: A cylinder has an ID of 100 mm and an internal pressure of 50 MPa. Find the needed wall thickness if…

A: Given data: cylinder Internal diameter=Di =100mm Internal pressure=Pi…

Q: A rubber block with dimensions 120x120x120 mm is a rigid mold It is compressed with a vertical force…

A: Given data: The dimensions of the rubber block are 120 mm×120 mm×120 mm. The vertical force acting…

Q: The principal stresses at a point in a critica section of a machine component are o, = 60 MPa a, =5…

A: Given:σ1=60 MPaσ2=5 MPaσ3=-40 MPaσy=200 MPa

Q: At a point in a material under stress, the intensity of the resultant stress on a certain plane is…

A: Draw the Mohr circle indicating the resultant stress on the plane. Write the expression for the…

Q: A 6 mm thick plate is to be punched of a shape shown in figure. Determine the minimum punching force…

Q: Imagine that a long steel wire hangs vertically from a high-altitude balloon.(a) What is the…

Q: A one mm diameter steel wire is wounded around a copper tube with external and internal diameters of…

A: Given: The diameter of wore, d = 1 mm The external diameter of tube, Do = 140 mm The internal…

Q: Suppose a long bone is idealized as a solid cylinder with a diameter of 0.03 m. During a torsion…

Q: A small element is under loading where ox =-22 MPa, ơy =22 MPa and txy =14 MPa. Taking the yield…

A: Given data:

Q: e 3 m high is fixed at the base. It is 6mm thick and its outside diameter is 300mm. The pole is…

A: Given:h=3 mt=6 mmD=300 mmT=25 kN.mF=3 kNG=78 GPaζallow=60 MPa

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

A: Relation between the stresses in the bronze and the steel…

Q: At a point in a steel structure (Y = 490 MPa, E = 200 GPa, v = 0.29), the principal stresses are oj…

Q: Yielding starts in a material when the principal stresses are 100 MPa, 100 MPa and 200 MPa. As per…

A: Givenσ1=100MPaσ2=100MPaσ3=200MPa

Q: 7. A wooden storage vat is 6 m in diameter and is filled with 7 m of oil, s = 0.8. the wood staves…

Q: 2.29. A cylindrical steel shaft is required to transmit a bending moment of 1000 Nm and a torque of…

Q: A thin-walled cylindrical tube with internal diameter and thickness of 50 mm and 0.5 mm,…

A: Given:Internal diameter of tube, di=50 mmthickness, t=0.5 mmPressure, P=2 MPaMagnitude of moment,…

Q: A compound thick cylinder has a bore of 100 mm diameter, a common diameter of 200 mm and an outside…

Q: Derive the following equation for computing shear stress in a solid bar along an oblique plane with…

Q: A punch for making holes in steel plates assumes that having a diameter of 0.75 in. is used to punch…

Q: Q2 Consider a low-carbon square steel bar 30 mm on a side and 1.7 m long having a material yield…

A: Given Data: Width of the bar, w=30 mm Length of the bar, l=1.7 m=1700 mm Yield of the bar, σy=275…

Q: Figure shows a cantilever shaft made of steel subjected to several loading T=5kNm, M=2.5kNm, and…

Q: Find Young's Modulus, yield stress, ultimate stress, percentage elongation and percentage reduction…

A: Given:- D=25mm Gauge length=200mm Least count=0.001mm At load 30kN, extensometer reading=60 At load…

Q: A bar is subjected to fluctuating tensile load from 20kN to 100KN. The material has yield strength…

A: As per given question Fluctuation tensile load P1=20kn…

Q: The Mohr's circle of plane stress for a point in a body is shown. The design is to be done on the…

A: Given:Mohr's circle of plane stress

Q: For a state of plane stress, if, o,=80 MPa o,=40 MPa, and T=0 MPa, then according to our…

Q: Steel strip has to be formed as shown in Figure Q3, with a bend of inside radius of 400 mm and bend…

A: Given: Inside Radius of the bend is 400 mm. Bend angle is 30 deg. Calculation: (i) When a strip is…

Q: Example 133: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm,…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

(i) Von Mises yield criterion
(ii) Tresca yield criterion

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A mild steel shaft of 40 mm diameter is subjected to a bending moment of 115 N-m and torque, T. If the yield point of the steel in tension is 300 MPa, find the maximum value of torque T without causing yielding of the shaft according to von-Mises and Tresca failure theories.
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Calculate the maximum shear stress with Mohr's circle? d) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion?
Steel railroad reels 15 m long are laid with at an initial temperature Ti = 46 °C. Assume α = 11.7 μm/(m·°C) and E = 200 GPa. What stress would be induced in the rails in MPa at a final temperature of Tf = 107 °C, if there were no initial clearance?
For a given material, Young’s modulus is 100GPa and shear modulus is 40GPa. Find the bulk modulus and lateral contraction of a round bar of 40mm diameter and 2.5 m long when stretched 2.5 mm.
A scuba tank is being designed for an internal pressure of 1600 psi with a factor of safety of 2.0 with respect to yielding. The yield stress of the steel is 35,000 psi along its hoop direction and 16,000 psi in longitudinal direction. If the inside diameter of the tank is 7.0 in., what is the minimum required wall thickness? (Show complete calculation and step by step process. Show free body diagram)
A mild steel shaft of 50 mm diameter is subjected to a bending moment of 2000 N-m and a torque T. If the yield point of the steel in tension is 200 MPa, find the maximum value of this torque without causing yielding of the shaft according to The maximum principal stress; The maximum shear stress; and The maximum distortion strain energy theory of yielding
Imagine that a long steel wire hangs vertically from a high-altitude balloon.(a) What is the greatest length (feet) it can have without yielding if the steel yields at 44) ksi?(b) If the in wire hangs from a ship at sea, what is the greatest length? (Obtain the weight densities of steel and seawater from Table I-I. Appendix I.)
A mild steel shaft of 60 mm diameter is subjected to a bending moment of 2200 Nm and a torque T. If the yield point of the steel in tension is 200 MPa, find the maximum value of this torque without causing yielding of the shaft according to:1. The maximum principal stress theory;2. The maximum shear stress theory; and3. The maximum distortion strain energy theory of yielding
A thick-wall underwater pipe is placed at 20m below sea level. The pipe is carryingcompressed natural gas with pressure of 50 MPa. The pipe has 115mm outer diameter andmade of 316 stainless steel with yield strength of 205 MPa. The density of sea water could betaken as 1029 kg/m3. Find out:a) What is the resultant outer pressure acting on the underwater pipe? b) What is the minimum inner diameter to ensure the pipe does not yield?c) Sketch the variation of hoop and radial stress across the pipe wall, completed with stresslabelling. d) What is the resultant longitudinal stress of the pipe?
With a thick walled cyclinder the inner radius is 0.05m and out radius is 0.2m. The internal pressure is 200 MPa - What is the hoop and radial stress at the inner surface? - What would be a suitaable material for the cyclinder under von mises criterion?
Consider a hollow steel shaft with a 130mm outside diameter and a 70mm inside diameter. What is the maximum torque that this shaft can transmit if the shear yield stress is 1.4 x 108Pa and the behavior is elastic, perfectly plastic?
A sheet metal cutting machine cuts the sheet metal via shear force, V as shown in Fig. 1. The crosssection of sheet metal is rectangular with width, b = 3m and thickness, d = 5mm. The sheet metal ishaving yield strength σy = 220 MPa; Young’s modules, E = 200 GPa and Poisson’s ratio, ν = 0.3.Conduct the following analyses at the state of stress when maximum stress reaches σy and beforeshearing commences. (Need answer Question c) & d) c. Sketch the YIELD LOCI for both cases above. d. As a sheet-metal engineer, which failure criterion in (b) will you use to determine the cuttingshear force? Explain the reason for your answer.