What is the diameter of the pipe at L= 1,2 and 3 m from the 1-1 end For aTapered pipediameter of the pipe atas shown below, whar is2.)ス= ゴmüi) l-3mLength of the Pipe L= 6m0.5m13DDiameter at 1-1=Diame ter at 2-2 = 1,5mTwant to know the me thod how to find itsojexplain properly.

Answered: Image /qna-images/answer/94c24588-bc83-4796-bca3-68e5426000a4.jpg

Answered: For diameter of the pipe at 女 (a pered…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Discussion 1- Indicate the factors affecting the Reynotes number (Re). 2. The limits are gaved to the Reynolds number (Re) that if they less than 2000 it is the laminar flow and if they more than 4000 The flow is turbubent but there is a possibility to change those limits. 3-Discuss the importance of the infinite medium. Worksheet No. Risc of W.L. in Time for Risc in Collecting Tank (cm) W.L. (sec.) 1 s 45 2 s 26.5 3 s 21.5 4 % 12.75 s s 7 6 s s Diameter of pipe = 1.8 cm Length of pipe = 87 cm Area of Collecting Tank = 13 x 8.5 cm® @ Temperature of water = 30
choose the correct answer Q1A- Losses of pressure in fluid due to resistance by viscose shear stresses are: * a) Minor losses b) Fitting losses c) Friction losses d) Total head losses e) None of all above B- when pipe with the different diameter are connected by series, then total losses will be the sum of each pipe losses * a) True b) False
Answer is hL = 17.6m
in the experiemnt of Pipe Energy Losses Laboratory Design Exercise these equipment are used fill in the descriton of each item braifely in 1 or 2 senteces each
Benzene (u=3.95 x10-4Pa-s) at 60°C is flowing in a 24.3mm steel pipe (absolute roughness =4.6 x10-5m from moody diagram) at the rate of 20L/min. The specific weight of the benzene is 8.62 =kN/m³. Calculate the pressure difference between two points 100m apart if the pipe is horizontal.
A 0.5-inch diameter water pipe is 18 m long and delivers 19 L/min. What fraction of this pipe is taken by the entrance region?[Ans. LE /L=1.7%]
A smooth plastic pipe is to be designed to carry 10 (ft^3)/s of water at 77°F(25°C) through 1800 ft of horizontal pipe with an exit pressure at 25 psig. The pressure drop is to be approximately -300 psig. Determine the minimum pipe diameter (in inches) that will result in the given pressure drop. For water at 77°F: ρ = 1.934 slug/(ft^3), and μ = 1.86E-5 slug/(ft-s). Round your answer to 2 decimal places.
A differential pitot tube located at the center of a cylindrical air tube produces 2.6 in. of water pressure. What is the velocity at the impact end of the pitot tube? The impact gauge reads 2.6, 2.6, 2.5, 2.1, 1.8 when placed at points 1-5 in Fig. 3.10. What is the average velocity in the tube? What factor would be applied to the center reading to indi- cate a true average velocity? Note: In actual practice it would be necessary to check this factor through the entire range of velocities to be encountered, because variation may be expected.
With the given pipe lengths, sizes and connections and if all pipes have an f=0.020. 1. which of the following most nearly gives the flow in pipe 2? a. 7 cfs b. 6 cfs c. 5 cfs d. 11 cfs 2. which of the following most nearly gives the head loss between B and C? a. 60 ft b. 100 ft c. 40 ft d. 80 ft with solution pls
Question : SAE 30 oil at 20°C flows in the 3.5-cm-diameter pipe, which slopes at 37°. For the pressure measurements shown, determine Part (a) whether the flow is up or down and Part (b) the flow rate in m3/h. Neglect minor losses. Directions - Solve carefully, Write Clear, Label as Part (A) and (B) Circle Final answer(s) Hint : flows in the 3.5-cm-diameter pipe, *** USE IMAGE BELOW Pb = 190kPa, Pa = 550kPa, 25m, etc
Calculate pressure loss in a pipe ( d = 55 mm, L = 200 m ), for oil mass flow rate of 133 kg/min. Oil density is 900 kg/m3and kinematic viscosity is ν = 4·10-5 m2/s. The sum of local losses in the pipe is 3,5. Round off the answer to one decimal digit in kPa, but enter the answer without the unit.
Water is flowing through a horizontal tube According to the figure . It's diameter at 2 points are 0.3 m & 0.1 m respectively . Pressure difference between 2 points is equal to 0.8 m of water coloum . Find rate if flow in the tube

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

For diameter of the pipe at 女 (a pered pipe as shown below, what is a )ス= ゴm üi) l-3m Lengih of the pipe L= 6m Diameter at 1-1=0. Sm Diameter at 2-2= 1,5m Iwant to know the me thod how to find it soiexplain properly·