I need the answer as soon as possible Calculate the flow rate of water (p = 1.94 slug/ft3), if the pressure difference, P-P2,is measured as 707.97 lbf/ft2 of mercury (sp. gr. for mercury is 13.6). For an orificemeter with a 1 inch orifice diameter in a 3 inch diameter pipe. The orifice coefficient forthis meter has been determined to be Ca 0.62 under these flow conditions.

Answered: Image /qna-images/answer/8bfcb699-d169-4e33-bfbf-2cbd3e76b3d8.jpg

Calculate the flow rate of water (p = 1.94 slug/ft'), if is measured as 707.97 lbf/ft2 of mercury (sp. gr. for mercury is 13.6). For an or meter with a inch orifice diameter in a 3 inch diameter pipe. The orifice coefficien this meter has been determined to be Ca=0.62 under these flow conditions.

Calculate the flow rate of water (p = 1.94 slug/ft'), if is measured as 707.97 lbf/ft2 of mercury (sp. gr. for mercury is 13.6). For an or meter with a inch orifice diameter in a 3 inch diameter pipe. The orifice coefficien this meter has been determined to be Ca=0.62 under these flow conditions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(Q26) A horizontal Venturimeter with inlet radius 110 mm and throat radius of 55 mm is used to measure the flow of water. The pressure at inlet is 20 N/cm2 and the vacuum pressure at the throat is 27 cm of mercury. Find the rate of flow. The value of cd may be taken as 0.9
Data: Hp2,3 = 2 m; A3 = 20 cm²; A₂ = 1 cm²; Hp0,1 = 0.8 m; NB= 74%(pump efficiency) To determine: a) the flow (L/s); b) the area of section (1) (cm³); c) the power supplied by the pump to the fluid.
7.) The pressure drop associated with hydraulic fluid with a Sg of 0.93 flowing across a 1-in. I.D. sharp edge orifice is 20 lbf/in2 . If the discharge coefficient is 0.60, what flow rate in gal/min could be expected through the orifice?
An orifice meter with orifice area 804 mm2 is inserted in a pipe of area 1608 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 80 cm of mercury. Find the rate of flow of oil of sp. gr. 0.8 when the co-efficient of discharge of the orifice meter = 0.5. 1) Head of water (in m) 2) The discharge of water through pipe (in Litres/sec)
A 0.30 m X 0.40 m branch duct leaves a 0.30 m X 0.60 m main duct at an angle of 60°. The air temperature is 20°C. The dimensions of the main duct remain constant following branch. The flow rate upstream is 2.7 m3/s. Find the pressure downstream in the main duct if at 20°C, the mass per unit volume is 1.2041 kg/m3. Group of answer choices 436 Pa 634 Pa 643 Pa 346 Paplease show full soluton for review and analysis
A pump is installed to deliver water from a reservoir of surface elevation zero, to another of elevation 290 ft. The 10 inch-diameter suction pipe (f=0.022) is 90 ft long and the 8-in-diameer discharge pipe (f=0.028) is 4900 ft long. The pump characteristic is defined by hp= 365-20Q2 where hp, the pump head, is in feet and Q is in cubic feet per second. What is the rate at which the pump will deliver the water?
9.7. Through a hydraulic turbine flow 2.8 m3/s of water. On the 1 m inlet pipe at elevation 43.5,a pressure gage reads 345 kPa. On the 1.5 m discharge pipe at elevation 39, a vacuum gage reads150 mm of mercury. If the total head lost through pipes and turbines between elevations 43.5and 39 is 9 m, what power may be expected from the machine?
1Two water pumps are arranged in series. The performance data for both pumps follow the parabolic curve fit Havailable =H0 =aV ^2. For pump 1, H0 =5.30 m and coefficient a =0.0438 m/Lpm^2; for pump 2, H0 =8.70 m and coefficient a =0.0347 m/Lpm^2. In either case, the units ofnet pump head H are m, and the units of capacity V are Lpm.Calculate the combined shutoff head. Complete Answer, thank you
2. A fan discharges 265 cu.m/min of air through a duct of 92 cm in diameter against a static pressure of 0.022 m of water. The fluid density is 995 kg/cu.m., the air temperature is 29°C and the barometric pressure reading is 730 mm Hg. If the power input to the fan is measured 3.5 hp, what are the total and static fan efficiencies?
In a test of the centrifugal pump shown in Fig. , thefollowing data are taken: p1= 100 mmHg (vacuum) andp2 = 500 mmHg (gage). The pipe diameters are D1 = 12 cmand D2 = 5 cm. The flow rate is 180 gal/min of light oil(SG = 0.91). Estimate (a) the head developed, in meters,and (b) the input power required at 75 percent efficiency.
Paolo owns a hydroelectric power generating system as shown in HG008. Water flows from an upper reservoir to a lower one passing through a turbine at the rate of 150 lps. The total length of pipe connecting the two reservoir is 100 m. The pipe diameter is 250 mm and the Hazen – Williams coefficient is 120. The water surface elevations of reservoirs 1 and 2 are 197 m and 50 m, respectively. Find the velocity of flow in pipe in m/s.
An oil of specific gravity 0.9 is flowing through a venturimeter with inlet diameter of 300 mm and throat diameter of 205 mm. A differential manometer connected to the inlet and throat of the venturimeter gives a difference in the reading of 27 cm of mercury. Take coefficient of discharge of the venturimeter (Cd) as 0.96. Find the following Inlet area of the Venturimeter (in m2) Answer for part 1 Throat area of the Venturimer (in m2) Answer for part 2 Differential pressure head 'h', (in m of oil) Answer for part 3 Discharge of oil through Venturimeter (in m3/s) Answer for part 4 Discharge of oil through Venturimeter (in Litre/s)