For automobile engines, opening and closing of valves is operated by O a. flywheel mechanism b. cam shaft c. any shaft that rotates with high speed d. crank shaft

Q: Q1- Explain the duties of camshaft, distributor and alternator, which are among the engine parts

A: Camshaft Camshaft is the shaft at which many cams are connected and it operates with the crankshaft.…

Q: The inside of a hydraulic power unit is shown. Identify parts B,C, and D

A: Solution: Given Data:

Q: Compare between Two of the following -Open System and close system.

A: Note: As there are multiple questions posted at once. I will be answering the first question. Please…

Q: introduction about Control of Pneumatic Cylinder with AND and OR Functions

A: Pneumatic cylinders (also known as air cylinders) are mechanical devices that generate force in a…

Q: Differentiate between single acting and double acting cylinders.

A: Differentiate between Single Acting & Double Acting Cylinder :

Q: The hydraulic cylinders is also known as

A: The hydraulic cylinder is a mechanical actuator which convert hydraulic energy  into the mechanical…

Q: H8/e8, the toleran tol de orit of

A:

Q: Master cylinder that is the terms used in

A: Brake  Pump

Q: Explain with the aid of schematic diagram the working operation of two pressure valve and shuttle…

A: Twin pressure valve: Draw the schematic diagram of the twin pressure valve.

Q: Briefly describe the definition of hydraulic radius.

A: HYDRULIC RADIUS…

Q: DIOCK orce experienced by both the

A:

Q: Explain with neat sketch of crank and lever mechanism used in oil and gas industry.

A: Crank and slotted lever mechanism:-

Q: It's known that the mechanism is a 4-bar

A: Drawing the kinematic diagram of the mechanism as shown below, (a) Calculating DOF: DOF can be…

Q: placed by oil in the wate

A: Given Data : Water is replaced by oil in water pump

Q: Which type of the pump is different from others in the same group? Select one: a. Piston pump O b.…

A: We have to find  Which type of the pump is different from others in the same group ?

Q: The capacity control for a screw compressor is accomplished with cylinder unloading true or false

A: A rotary compressor makes use of a rotary type displacement mechanism. These compressors are usually…

Q: With a neat sketch explain the Analysis of simple hydraulic Jack.

A: Jacks are pieces of industrial heavy equipment that raise or move heavy loads by multiplying force.…

Q: The factor of safety for the piston rod is

A: Given data; diameter (d) =20mmlength (l)=700 mmforce=10 kNYOUNG MODULUS=200 GPa acc. to question we…

Q: B2. Explain the function of Thermocouple with neat diagram and mention its advantages.

A: The thermocouple is a thermoelectric device that is used for temperature sensing. It is based on See…

Q: - Low-speed shaft - Gearbox JI Rotor Hub- kel - High-speed shaft k2 Nacelle- Blade de

A: Solution

Q: 1) Draw a simple sketch of your regulator design 2) Draw a simple sketch of the spring

A:

Q: 1. Explain with neat sketch of crank and lever mechanism used in oil and gas industry.

A:

Q: For a hydraulic power unit, this part supplies the energy to cause the shaft of the pump to rotate.…

A: Option a is correct.

Q: Define the term in theory of macines Meyer's expansion valve

A: The Meyer's expansion valve consists of two valve known as  main valve and expansion valve which are…

Q: e power output from

A: Need to calculate the power output.

Q: Describe the functions of the hydraulic systemcombination valve.

A: Hydraulic fluids today are used for a variety of things. A hydraulic fluid's primary role is to…

Q: a hydraulic tu the full scale of the full scal

A:

Q: For a hydraulic power unit, this part limits the system pressure to safe levels a. reservoir b.…

A: Option d is correct

Q: Determine the maximum, minimum and average pressure in a plate clutch

A: Given data;  Axial force(W)=4kn=4×103 NInside radius (r2)=50mmoutside radius(r1)=100mm Assume…

Q: The bolt size of cylinder head in a reciprocating compressor is a. M16

A: The bold size of the cylinder head in a reciprocating engine M16 option (a) is correct.

Q: 3. With a neat sketch explain the Analysis of simple hydraulic Jack.

A:

Q: /5 --- A computer cannot "boot" if it does not have the

A: An operating system is the system software that handles the software and hardware resources and…

Q: An oil leak at the bellows of a rack and pinion could be caused by ______.

A: As per given question  What is the cause of Oli leak at bellows of a rack and pinion

Q: In most of internal combustion engines, crankshaft bearing is  Select the correct answer below: A.…

A: Concept: Hydrodynamic bearing: 1) In this bearing, two rubbing surfaces of bearing are separated by…

Q: verno

A: governor: In technology, a governor is a mechanism that keeps the rotational speed of an engine or…

Q: 7.4 Draw the symbols for (a) a pressure-relief valve, (b) a 2/2 valve which has actuators of a…

A:

Q: rom the ov when the in Car Cand theo

A:

Q: B2. Explain the function of Thermocouple with neat diagram and mention its advantages. [-

A: A Thermocouple may be a sensor utilized to degree temperature. Thermocouples comprise of two wire…

Q: Describe with mechanism abut how a boiler feed water telreatment sytem work

A: given; Describe with mechanism about how a boiler feed water treatment system work

Q: Choose correct answer: Which of the following is not under the type of a gas charged or filled…

A: A gas-charged or filled accumulator uses the pressurized gas as a compressible medium to store the…

Q: Which of the following system is suitable for automatic bottle filling operations used in food…

A: Automatic Bottle Filling Machines are used in soft drink industries. These machines use a conveyor…

Q: 11. Fluid sealing in a dashpot is achieved using

A: GIVEN DATA A MCQ GIVEN ASKING WHICH SEALING USED IN FLUID DASHPOT SYSTEM

Q: The clutch, or friction, disc is connected to the

A: The clutch, or friction, disc is connected to the....

Q: ed vessel contains 3 k che vessel till the ga k done on or by the ga

A:

Q: Transmission angle is the angle between and link of a four bar mechanism

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.