For combined cycle, which statement is incorrect Select one O a Increasing the live steam temperature improves the thermodynamics of the cycle Ob Increasing the live steam temperature increases the steam process efficiency Oc Increasing the live steam temperature reduces wetness in the low pressure turbine section. Od Increasing the live steam temperature reduces the rate of waste heat energy.

For combined cycle, which statement is incorrect Select one O a Increasing the live steam temperature improves the thermodynamics of the cycle Ob Increasing the live steam temperature increases the steam process efficiency Oc Increasing the live steam temperature reduces wetness in the low pressure turbine section. Od Increasing the live steam temperature reduces the rate of waste heat energy.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What are the disadvantages of a Regenerative Rankine Cycle?
A simple ideal Brayton cycle uses argon as the working fluid. At the beginning of the compression, P1 = 15 psia and T1 = 80°F; the maximum cycle temperature is 1200°F; and the pressure in the combustion chamber is 150 psia. The argon enters the compressor through a 3 ft2 opening with a velocity of 200 ft/s. Determine the rate of heat addition to this engine, the power produced, and the cycle’s thermal efficiency.
In an ideal dual combustion cycle the pressure volume and temperature at the beginning of the adiabatic compression are 93 kN/m^2,0.05m^3 and 24°c respectively.The volume ratio of the adiabatic compression is 9:1 the constant volume heat addition pressure ratio is 1:5:1 and the constant pressure heat addition volume ratio is 2:1 Determine for the cycle a) the work ratio b) the mean effective pressure c) the Carnot cycle within the cycle temperature limits
How does the a Regenerative Rankine Cycle improve the simple rankine cycle?
d) the thermal efficiency (%) of the cycle. e) Sketch the cycle on a T-s diagram, showing all states and processes. Assume the compressor and turbine isentropic efficiencies are both 80% and that the regenerator effectiveness is 70%.
1.5An ideal Rankine cycle with reheat uses water as the working fluid. As shown in the figure below, the conditions at the inlet to the first turbine stage are 1600 lbf/in.2, 1200°F and the steam is reheated to a temperature of T3 = 800°F between the turbine stages at a pressure of p3 = p2 = 200 lbf/in.2 For a condenser pressure of p5 = p4 = 1 lbf/in.2, determine:(a) the quality of the steam at the second-stage turbine exit. h6≈h5+v5(p6−p5)h6≈h5+v5(p6-p5)Determine the quality of the steam at the second-stage turbine exit. x4 =(b) the cycle percent thermal efficiency.
In an ideal Reheat cycle , the steam throttled condition is 7 Mpa and 460 C. The steam is then reheated to 1.5 MpA and 460 C . If turbine exhaust is 50 C ,determine the following: A.) Quality after turbine expansion B.) Turbine work C.) Heat added in the boiler D.) Heat rejected from the condenser E.) Pump work F.) Net work G.) Cycle efficiency
The isentropic efficiencies of the expansion and compression processes are 90%. The specifi c steam consumption of the Rankine cycle is 2 kg / kW h, having Work of Turbine and Work of pump equal to 2000 kJ/kg and 199 kl/kg respectively. Calculate the ideal SSC, W, and W.
Consider a simple ideal Rankine cycle and an ideal regenerative Rankine cycle with one open feedwaterheater. The two cycles are very much alike, except the feedwater in the regenerative cycle is heated byextracting some steam just before it enters the turbine. Compare the efficiencies of these two cycles. Showyour complete solution and diagram’s.
An ideal Otto cycle operates at a compression ratio of 8, an initial temperature and pressue of 70oF and15 psia, and a maximum cycle temperature of 3540oF. What is the cycle efficiency? a. 0.206 b. 0.138 c. 0.249 d. 0.504
IDEAL RANKINE CYCLE: In an ideal Rankine Cycle, steam at 5 MPaa and 500 o C enters the turbine and expands 300 KPaa. For 110,000 kg/hr of steam, find: a) Ideal power output of the Turbine (kW), b) Power to drive the pump (kW), c) Rate of Heat Added (kW), d) thermal efficiency of cycle and engine, e) steam rate of the cycle and engine, f) Heat Rate (PLEASE SHOW COMPLETE SOLUTION AND ENCLOSE ALL THE FINAL ANSWERS ROUNDED OFF TO THE 4TH DECIMAL)
Why is cp not used in the Stirling cycle analysis?