For nos. 21-23, satisfy the conditions of the given problembelow: As an airplane's brakes are applied, the nose wheelexerts two forces on the end of the landing gear asshown in the figure 1. Determine:21. the force in the strut AB. *1 ft-20%2 ft1350 lb30%450 lb.A. 215.3 lbB.224.4 lbC. 233, 2 lbD. 234.3 lbOption 522. the horizontal component at the pin C. *A. 628.6 lbB. 627.8 lbC. 634.4 lbD. 652.3 lb23. the vertical component at the pin C.A. 1468 lbB. 1485 lbC. 1500 lbD. 1526 lb

Answered: Image /qna-images/answer/a59d5694-ecfc-41e2-9c78-50d22e9589c2.jpg

For nos. 21-23, satisfy the conditions of the given problem below: As an airplane's brakes are applied, the nose wheel exerts two forces on the end of the landing gear as shown in the figure 1. Determine:

For nos. 21-23, satisfy the conditions of the given problem below: As an airplane's brakes are applied, the nose wheel exerts two forces on the end of the landing gear as shown in the figure 1. Determine:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

M16 (h=2mm, d1=13.54mm, d2=14.7mm) material quality 8.8 bolt-nut connection Blowout= 2500 daN prestressbored with. Factor of safety S=2.5, key length L=10.d, coefficient of friction µo='=0.17; Average of contact surface with nutdiameter is given as d0=1.4.d. According to the given;a) strength control calculation during tightening;b) hand force that must be applied to the wrenchc) When the pre-tensioning force is applied, the elongation of the part is given as lp= 0.015mm, and the elongation of the bolt as lc= 0.030mm. BusinessSince the total elongation of the bolt is lctop=0.040mm for Ftop=3000 daN after the force is applied, we can define the characteristic of the bolt.find it.d) the characteristic of the part and the minimum remaining shortening value önlp after the prestressing forcee) Calculate the portion of the operating force on the bolt (Fic) and the part (Fip).f) Calculate the pre-tension force Fön' value remaining in the connection after the operating force has been…
...Two pulleys with diameter 500 mm and 1200 mm are connected by crossed belt drive. If the belt transmits 20 hp and the distance between the shafts is 4 m, which of the following is the angle of contact between the belt and the pulley?Group of answer choices 0.3 rad 2.8 rad 0.4 rad 3.5 rad
A 4 inches diameter shaft is driven at3600 rpm by a 400 Hp motor. The shaftdrives a 48 inches diameter chainsprocket having an output efficiencyof 85%. The output force of thedriving sprocket and the output of the driven sprocket are: A.200 lb and 250 hp B.261.6 lb and 300 hp C.291.66 lb and 340 hp D.None of the above Ans. C Please provide me a solution that corresponds to the correct answer.
Provide a very clear and complete solution as well as diagram. A pulley 600 mm in diameter transmits 40 KW at 500 rpm. The arc of contact between the belt and pulley is 144 degrees, the coefficient of friction between belt and pulley is 0.15 and the safe working stress of the beltis 2.1 Mpa. Determine the belt tension ratio, neglecting the effect of centrifugal force. A. 2.41 B. 2.44 C. 1.458 D. 4.1
In the design in the figure, a force of Fn=45992 N acts in the vertical plane on a machine element with a diameter of D=200 mm on the shaft resting on the A and B bearings. If the angle made by this force with the horizontal is b=40o, find the life of the 6210 coded Deep Ball bearing to be used in the B bearing, in hours. Number of revolutions = 30 rpm. 1-) The diameter of the machine element on which the force acts will be taken into account in the calculation of bearing forces (That is, it will be assumed that the Fn force AFFECTS THE GROUND shown in the figure, NOT the axis of the shaft). 2-) Pi number will be taken as 3.14.
Total Load = 40 + 150 + 100 + 60 + 40 = 390KNRD = 217.62 RB = 172.38 Don't skip solutions thanks!
MACHINE DESIGN TOPIC A short compression member with Do = 2Di is tosupport a dead load of 25 tons. The material isto be 4130 steel, WQT 1100 F. Calculate theoutside and inside diameters in terms of incheson the basis of (a) yield strength, (b) ultimatestrength.*For 4130 steel, WQT 1100 FSu = 127 ksiSy = 114 ksi*Use the following Safety FactorsNu = 4Ny = 2
Compare each strength gain and relate its significance on Strength and Economy. The design strengths are: a.) 290.7 kNm (using 4-25mm dia. Tension bars) b.) 378.7 kNm (using 6-25mm dia. Tension bars) c.) 385.97 kNm (using 9-25mm dia. Tension bars)
The Euler’s theory holds good for ________ Select one: a. Long column b. Short column c. Short shaft d. Long shaft
What is the strength ratio for a 160 lb (72.7 kg) client who has a 10RM of 180 lb (81.6 kg) on the bench press?a. 1.3b. 1.5c. 1.7d. 1.9
An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter of an input shaft is d = 20 mm and its material is 16MnCr5. A force of F = 2800 N forces the shaft due to the operation of a gear wheel connected with a wedge on the input shaft. The distances of the gear from the bearings are given as L₁ = 40 mm and L2 = 60 mm. In the most dangerous section, you are required to check the strength according to the S = 3 safety factor. If the section is unsafe in terms of strength, what changes would you make in the design to make it safe? (The surface of the spindle is machined as fine chips, reliability poor Kg = 1.).
given: - initial length of steel tube= 200mm - aluminum rod is 0.175 mm shorter than steel tube. - l=0.175 mm properties of materials - ALUMINUM: coefficient of linear expansion: 23x10-6 /C modulus of elasticitty= 70 GPa - STEEL Coeficient of linear expansion: 11x10-6 /C Modulus of elasticity: 200 GPa *NEGLECT SHEAR AND LATERAL DEFORMATIONS. REQUIRED: - which of the two members will have contact on the rigid switch first and at what temperature - axial stress that would develop on 1st member after the 2nd material fills in the gap safely. PLS. SHOW FULL SOLUTIONS WITH BRIEF EXPLANATIONS AND NECESSARY DIAGRAMS...