For the circuit shown as Figure Q4, use loop equations to determine the values and direction of the currents flowing-in each of the batteries and in the 10 2 load resistor. Calculate the voltage across the load resistor. [Answers: 1.625 A discharge;0.75 A charge; 0.875 A; 8.75 V ] + 12 V 2Ω 8 V 1Ω Figure Q4 Load 10 Ω

For the circuit shown as Figure Q4, use loop equations to determine the values and direction of the currents flowing-in each of the batteries and in the 10 2 load resistor. Calculate the voltage across the load resistor. [Answers: 1.625 A discharge;0.75 A charge; 0.875 A; 8.75 V ] + 12 V 2Ω 8 V 1Ω Figure Q4 Load 10 Ω

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 78AP: Consider the circuit shown below. (a) What is the terminal voltage of the battery? (b) What is the...

See similar textbooks

Similar questions

Would your headlights dim when you start your car's engine if the wires in your automobile were superconductors? (Do not neglect the battery’s internal resistance.) Explain.
Unreasonable Results Suppose you have a 40.0- galvanometer with a 25.0-A sensitivity, (a) What resistance would you put in series with it to allow it to be used as a voltmeter that has a full-scale deflection for 0.500 mV? (b) What is unreasonable about this result? (c) Which assumptions are responsible?
A battery has some internal resistance. (i) Clan the potential difference across the terminals of the battery be equal to its emir (a) no (b) yes, if the battery is absorbing energy by electrical transmission (c) yes, if more than one wire is connected to each let initial (e) yes, if the current in the battery is zero (e) yes, with no special condition required. (ii) Can the terminal voltage exceed the emf? Choose your answer from the same possibilities as in part (i).
Solve Example 21.5, but use loop abcdefgha instead of loop akledcba. Explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors.
Consider the circuit shown below. (a) What is the terminal voltage of the battery? (b) What is the potential drop across resistor R2?
If you were 10 design an electric healer using Nichrome wire as the healing element, what parameters of the wire could you vary to meet a specific power output such as 1 000 W?
A young man owns a canister vacuum cleaner marked 535 W [at] 120 V and a Volkswagen Beetle, which he wishes to clean. He parks the car in his apartment parking lot and uses an inexpensive extension cord 15.0 m long to plug in the vacuum cleaner. You may assume the cleaner has constant resistance, (a) If the resistance of each of the two conductors in the extension cord is 0.900 , what is the actual power delivered to the cleaner? (b) If instead the power is to be at least 525 W, what must be the diameter of each of two identical copper conductors in the cord he buys? (c) Repeat part (b) assuming the power is to be at least 532 W.
Consider the circuit below, (a) What is the initial current through resistor R2? when the switch is closed? (b) What is die current through resistor R2 when the capacitor is fully charged, long after die switch is closed? (c) What happens if the switch is opened after it has been closed for some rime? (d) If the switch has been closed for a time period long enough for the capacitor to become fully charged, and then the switch is opened, how long before the current through resistor R1 reaches half of its initial value?
Referring to Figure CQ28.6, describe what happens to the lightbulb after the switch is closed. Assume the capacitor has a large capacitance and is initially uncharged. Also assume the light illuminates when connected directly across the battery terminals.
A person with body resistance between his hands of 1.00 k accidentally grasps the terminals of a 20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation. (b) If the internal resistance of the power supply is 2000 , what is the current through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low-re si stance devices? Explain your reasoning,
Is a circuit breaker wired (a) in series with the device it is protecting, (b) in parallel, or (c) neither in series or in parallel, or (d) is it impossible to tell?
Is every emf a potential difference? Is every potential difference an emf? Explain.