For the system shown in Fig. 8-7, it is desired that |V =|V = 1 pu. The loads, as shown, are S = 6 + j10 pu and S, = 14 + j8 pu. The line impedance is j0.05 pu. If the real power input at each bus is 10 pu, calculate the power and the power factors at the two ends. %3D %3D %3D %3D V 10+ j15 V2 4+ j5 10+ j3 S -6+ j10 Sz 14 +j8

For the system shown in Fig. 8-7, it is desired that |V =|V = 1 pu. The loads, as shown, are S = 6 + j10 pu and S, = 14 + j8 pu. The line impedance is j0.05 pu. If the real power input at each bus is 10 pu, calculate the power and the power factors at the two ends. %3D %3D %3D %3D V 10+ j15 V2 4+ j5 10+ j3 S -6+ j10 Sz 14 +j8

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In relation to a load connected in Y, the expressions in the time domain of three neutral line voltages at the terminals are: VAN= 120 cos (wt+32°) V VBN= 120 cos (wt-88°) V VCN= 120 cos (wt+152°) V Write the expressions in the time domain of the line-line voltages VAB, VBC and VCA.
The figure below shows an RLC electrical network operating on alternating current. A load impedance Z of unknown value has been connected to the output of said network. a) Find the value of the load impedance Z, which is necessary to connect to the output of the given network to obtain the maximum average power transfer.b) Determine the value of the maximum average power transferred to the load found in the previous section.Note, the values of all impedances shown in the circuit are given in Ohms.
Q5. A single phase overhead transmission line has a supply voltage of 34 kV and a sending end current of magnitude 40 A at 0-8 p.f. lagging is feeding a certain load. The total resistance and inductance of the line are 5 and 21 mH respectively. Draw the practical circuit used and the devices necessary to perform this experiment. Then calculate the sending end power, receiving end current, voltage, power factor, receiving end power and line efficiency Vs 34000 Is 40 Cosos 0.8 R 5 Ps Ir Vr Cosor Pr n 21e-3
A transmission line with impedance of 0.085 + j 0.32 Ω is used to deliver power to a load. The load is inductive and the load voltage is 200∠0° Vrms at 60Hz. If the load operates at 20 kVA with a power factor of 0.75 determine the real and quadrature power losses in both the load and the line and the source voltage phasor.
The load impedance absorbs 2.5 kW and generates 5 kVAR. The sinusoidal voltage source develops 7.5 kW.1. a) Find the values of inductive line reactance that will satisfy theseconstraints.2. b) For each value of line reactance found in (a), show that themagnetizing vars developed equals the magnetizing vars absorbed.
NEED ASAP Pleas answer this problem Maximum Average Power Transfer Pls show full and complete solution
The sending-end voltage in the circuit seen is adjusted so that the load voltage is always 13,800 V(rms). The variable capacitor is adjusted until the average power dissipated in the line resistance is minimum. 1. a) If the frequency of the sinusoidal source is 60 Hz, what is thevalue of the capacitance in microfarads?2. b) If the capacitor is removed from the circuit, what percentageincrease in the magnitude of Vs is necessary to maintain 13,800V(rms) at the load?3. c) If the capacitor is removed from the circuit, what is thepercentage increase in line loss?
A ower system is operating at 1000Mw, 132kV, 50Hz, with 0.8 p.f. laging in parallelwith another line at 750OMW, 132kV, 50Hz with 0.707 p.f. lagging. Both are interconnectedat the station and when the compensating device is on, the overall power factor isimproved to 0.9 lagging. Suggest suitable capacitors, shunt and series. Individual loadsand combined load are to improve power factor to 0.9 in all cases.
low voltage systems In the circuit given below, single-phase powers connected to the single-phase network are given. If the effective value of the applied voltage is 220 V, the amplitude of the current drawn from the network(I) how many A?(Note: - sign indicates phasor state) A)142,85 B)119,34 C)129,16 D)137,86
Suppose the circuit shown represents a residential distribution circuit in which the impedances of the service conductors are negligible and Vg1=Vg2=120 0° V (rms). The three loads in the circuit are L1 (a new refrigerator, a coffee maker, and a microwave oven); L2 (2 incandescent lamps, a humidifier, and a ceiling fan); and L3 (a clothes washer and a clothes dryer). Assume that all of these appliances are in operation at the same time. The service conductors are protected with 20 A circuit breakers. Will the service to this residence beinterrupted? Why or why not?
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
A dc transmission facility is modeled by the approximate series circuit shown below. If the load voltage is known to be Vload= 458.3 kilovolt (kV) what is the power loss in the line in megawatt (MW)? what is the voltage at the source Vs in kilovolt? Write two(2) decimal places in your answer.