For the truss structure shown in the diagram below: a-4-m, b-3-m and P=20-KN B + a Question 1.4: If all the members are made of the same material (Steel) with modulus of Elasticity E= 200 GPa and have same cross-section area A= 800 mm^2, what is the vertical displacement at C? :[Enter solution in mm to the nearest first decimal point]

For the truss structure shown in the diagram below: a-4-m, b-3-m and P=20-KN B + a Question 1.4: If all the members are made of the same material (Steel) with modulus of Elasticity E= 200 GPa and have same cross-section area A= 800 mm^2, what is the vertical displacement at C? :[Enter solution in mm to the nearest first decimal point]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q.2 The bar is made of an aluminium alloy having a stress-strain diagram that can be approximated by the straight line segment shown. Assuming that this diagram is the same for both tension and compression, determine the moment the bar will support if the maximum strain at the top and bottom fibers of the beam is E max = 0.05. 630 560 420 (MPa) 0.006 0.025 0.05 100mm M € (mm/mm) 75mm
A rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stress of 150 MPa in steel rod and 70 MPa in bronze rod. 2 m -1.5 m |+1.5 m→ 10 Bronze A = 300 mm2 E = 83 GPa Steel A = 900 mm2 E = 200 GPa L=2 m L= 1.5 m
8. A rigid bar AB is supported by three rods. A load P = 250 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10°6 kN/m^2 and modulus of elasticity of steel is 200 x 10°6 kN/m^2. Steel rod A= 900 sq. mm Steel rod A= 900 2m sq. mm Copper A=1200 sq. mm 2m B 1m 1m Determine the deformation in the rods (in mm). * Your answer
A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an aluminum alloy (E = 10,000 ksi) pipe B as shown. The supports at the top of the rod and the bottom of the pipe are rigid, and the materials were unstressed before the load was applied. The cross-sectional areas of rods A and pipe B are 0.80 in2 and 3.00 in2 respectively. Determine The normal stress in rod A in ksi, The normal stress in pipe B in ksi and The displacement of plate C in inches. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 5 decimal places.
A rigid bar AB is supported by three rods. A load P = 375 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10^6 kN/m^2 and modulus of elasticity of steel is 200 x 10^6 kN/m^2. a. Determine the deformation in the rods (in mm).
2.4 The truss shown is the same as in Example 2.1 except that the area of bar ab is a variable. E = 200,000 MPa. (a) For what value of Aah is v. = 0? Is this a function of the magnitude of the applied load? (b) Is it possible to obtain zero u, by varying A? (c) Suppose the applied load were vertical rather than horizontal, would it then be possible to obtain zero u, by varying Aab? If so, for what value of Aab? What would be the corresponding v.? 500 kN Fah = +400.6 kN Aab 4 m 6 m 3 m Problem 2.4 Fac = -277.8 kN Aae = 8000 mm?
A two pinned end bars AB (copper) and BC (aluminum) is subjected to a horizontal force P = 90KN applied at pin B %3D as shown in the figure, determine the horizontal displacement of pin B. Aluminum: L= 1.5m, A= 1000mm2, E= 70 GPa Copper: L= 2.0m, A= 850mm², E= 120 GPa Degree: 45° Alumaum L-15m A=1000 mm E-70 GPa >P=90 kN Copper L=2.0m Aa550 mm E=120 GPa
2. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free. What is the largest load P that can be applied without exceeding stresses of 160 MPa in the steel rod and 65 MPa in the bronze rod? - 2.5 m 2 m 2 m Steel A=1000 sq. mm Bronze A=400 sq. mm E=200 GPa E=83 GPa L=1.6 m L=2.2 m P
Question # 4: Determine the state of stress at point A on the cross section of the beam at section a-a. Show the results in a differential element at the point. a a 0.5m 0.5m 30 kN 2 m 100mm 50mm A 10mm 10mm 180mm Section a-a 10mm
The figure below shows the cross-section of a beam that carries a vertical shear force, V= 72 kN. The distance from the bottom of the section to the NA is d= 267 mm and the moment of inertia of the cross-sectional area about the NA is I = 440 × 106 mm4. The maximum shear stress on this cross-section is: 60 mm 219 mm 225 mm NA ---- NA 36 mm ------ a 90 mm 90 mm d = 267 mm 225 mm 36 mm
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 102 GPa] with a cross-sectional area of A₁ = 200 mm². Bar (2) is an aluminum alloy [E = 72 GPa] with a cross-sectional area of A₂ = 640 mm². All bars are unstressed before the load P is applied; however, there is a 2-mm clearance in the pin connection at A. Assume L₁ = 1880 mm, a = 1060 mm, b = 620 mm, c = 480 mm, and L₂ = 1270 mm. If a load of P = 71 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. (1) L₁ b tc B (2) D L2
An aluminum bar having a cross-sectional area of 160 mm carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1 = 0.8 m; B2 = 1.0 m; B3 = 0.6 m. Determine the total deformation of the bars B1, B2 and B3 in mm. 35KN B1 B2 B3 10KN 15KN 30KN 2.5 B 1.79 C) 0.54 3.75 E 4.83