Answered: From the following Identify cutting…

Engineering

Mechanical Engineering

From the following Identify cutting tool formed by grinding the end piece of a steel stock is O a. O b. O c. d.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter6: Milling

Section6.2: Tools, Toolholding, And Workholding For The Vertical Milling Machine

Problem 1RQ: Many of the cutters used in machining are made of either __________________ or ____________________.

See similar textbooks

Related questions

Q: 11. Two cutting tools with tool life equations given below are being compared: Tool 1: VTº-1-150…

Q: What would be the lead of a ¾ inch diameter drill with an include angle of 118 degrees

Q: Find the commercial tap drill size for 1⁄2”-20

A: given: Find the commercial tap drill size for 1⁄2”-20 NF bolt.

Q: The tool has only one cutting edge and the cutting edge is made of high-grade material like carbide…

A: As per given question The tool has only one cutting edge and the cutting edge is made of high-grade…

Q: Which would you use for any of the following situations: Cutting on a smaller mill, a larger mill…

A: Given data: For cutting a smaller mill A larger mill with little clearance A smaller diameter…

Q: In a multi point cutting tool the positive rake angle is used to cut low tensile strength and…

Q: In drilling operation on lathe machine, the drill bit is fixed in O a. Carriage O b. Headstock С.…

Q: 1. What type of milling machine can be used to make the groove in the shaft? 2. The diameter of the…

A: 1. Grooves, elongated slots and break-throughs are produced or made for the purpose of receiving…

Q: determine the tool life

A: Given; Find tool life for maximum production rate ? Where, Tool changing time, T= 2.7 min…

Q: The angle of forst of c

A: Given; From given figure: A stepped shaft subjected to a twisting moment applied at BShear modulus…

Q: Prob.1. A broach is used to cut a keyway 8 mm wide, 5 mm deep in a box 64 mm long. Determine – | (i)…

A: Given data: The width of the keyway is w = 8 mm. The depth of the keyway is d = 5 mm. The length of…

Q: The spindle axis on a horizontal milling machine is referred to by which letter? O Y

A: Draw the schematic diagram for the milling machine.

Q: Calculate the spindle speed (rpm) for turning operation when the cutting speed is 186.00 m/min and…

A: Find the spindle speed Cutting speed = 186 m/sec External diameter = 38.50 mm

Q: 4. Name 4 types of cutting tool wears and explain what problem can happen if the depth of cut is…

A: Tool wear : It is breakdown and gradual failure of cutting tool due to regular operation on…

Q: - Formula for finding the correct tap drill size. o for English system o for Metric system - Cutting…

A: Please find the solution below

Q: lain the Principal Operation of a Lathe Mac

A: Lathe machine: It has a chuck that holds the workpiece and rotates it so that we can easily do the…

Q: Identify from the following lathe operation performed only by crossfeed. a. Parting off operation b.…

Q: Answer the following questions by circling True or False. 13. The cutting speed of the hydraulic…

A: As per Bartleby guideline we are allow to give answer of one question at a time so please post other…

Q: Drilling is usually performed with a rotating cylindrical tool that has .. cutting edges * O Two O…

Q: e type of chuck most suitable for holding ctangular chuck is

Q: 2 Types of lathe chuck 2 Classification of lathe tool holder 2 Types of shaper

A: Given question: Types of Lathe Chuck Classification of Lathe Tool holder Types of shaper The given…

Q: Center drilling operation performed on lathe machine uses a single-point cutting tool. Select one:…

A: Answer is false

Q: Shaper machine uses single point cutting tool for cutting mater Select one: True False

A: 1.true

Q: determine the tool life

A: Given data; Tool changing time, Ttc=19 min Taylor's tool life exponent, n= 0.3 Find tool life…

Q: an a thick saw blade be used as a broach. Why. Why is it difficult to make

A: As per the guidelines we are subjected to solve only one question at a time. Please repost the same…

Q: Why is there one driver gear and two driven gears in a hand drill

A: The hand drill is a portable drilling machine that is similar in design to a breast drilling machine…

Q: 3. Define the tools that must have during the Shaper Machine Operation.

Q: Increasing the cutting speed (Vc) affects the surface finish by:

A: The dimensional accuracy of the final product depends on the cutting speed.

Q: State and explain five cutting tool materials

A: Based on the different conditions there will be different types of cutting processes. The selection…

Q: L the Cutting edges on both the end and outside periphery of the In cutter. * Down milling Face…

A: Ans) : Face Milling

Q: The lead screw of a lathe with nut forms a

A: A screw pair consists of a turning motion and sliding motion. The screw pair has thread cut in…

Q: is the lathe operation, which is performed without the cutting tool moving parallel to the axis of…

A: Lathe is a machine tool which is used in the work shop to perform the various machining operations…

Q: What is the stroke per minute of a mild steel which cutting speed is 200 fpm having a total length…

Q: Angle between side cutting edge and axis of tool is known as: Back rake angle O Side rake angle Side…

A: Angle between side cutting edge and axis of tool is given as Side cutting edge angle or side cutting…

Q: Milling Machine tool is an example of two axes machines

A: Milling cutting tool is the is an example of two axes machines. Answer: True

Q: Identify the true statement from the following a. Unit of cutting speed in millimetre per minute b.…

A: There are various terms related to the machining operations, such as cutting speed, feed rate, depth…

Q: What depth of cut is needed for a ¾ inch wide keyway in a 3 inches diameter shaft?

A: find the depth of cut in shaft .

Q: ifferentiate 3 types of lathe machine in terms o

A: Lathe machine: Lathe machine has a chuck and the toolpost, Chuck is used to holding the workpiece…

Q: Identify the operations from the figure Turning Facing Chamfering O drilling

A: Facing process remove the material along diameter.

Q: What part of the lathe is used to set the feed rate of the cutting tool?

A: Part of the lathe is used to set the feed rate of the cutting tool is Quick Change Gear Box Quick…

Q: In drilling operation on lathe machine, the drill bit is fixed in _______. a. Tool post b. Carriage…

A: Ans_ D_ Tailstock

Q: From the following Identify cutting tool that has the cutting edge in the form of small tip made of…

A: Let us discuss about about given single point cutting tool

Q: Milling is an intermitted cutting operation”. Explain it.

A: A milling machine is a machine tool that cuts metal as the workpiece is fed against a rotating…

Q: 1- Which one of the following operation is not related to drilling? a) Threading b) Counter boring…

A: The correct option to the above question is Option (a). The threading is related to the cutting of…

Q: process used for cutting a gear on a milling machine is called The a. Gear forming b. Gear shaping…

A: Option c is correct

Q: The tool has only one cutting edge and the cutting edge is made of high-grade material like carbide…

A: Carbide is very hard material that is used for the purpose of the cutting tool formation.

Q: Clapper box is used for _______ during machining. a. Push the tool down during return stroke b. Lift…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

From the following Identify cutting tool
formed by grinding the end piece of a steel
stock is
а.
b.
С.
Od.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a machine test, a cutting speed of 100 m/min indicated the tool life as 16 min and a cutting speed of 200 m/min indicated the tool life as 4 min. Calculate the values of n and C.
Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
In CNC lathes, to maintain constant cutting speed when feeding of the tool from the circumference to the center of the workpiece, the spindle speed (n) is needed to be: a/Increased b/Decreased c/Maintained the same
In a machining operation, doubling the cutting speed reduces the tool life to 1/8th of the original value. What is the exponent n in Taylor's tool life equation VTn = C,
During turning tests, using a cemented carbide tool resulted in a 1‑min tool life at a cutting speed = 4.8 m/s and a 22‑min tool life at a speed = 2.0 m/s. (a) Find the n and C
A part to be turned in an engine lathe must have a surface finish of 1.6 μm. The part is made of a free machining aluminum alloy. Cutting speed = 150 m/min. The nose radius on the tool = 0.75 mm. Determine the feed that will achieve the specified surface finish.
Specify cutting tool angles for a single-point cutting tool and usage of each angle with aid of aclear sketch.
Identify and explain the method of milling process in which the stresses on the teeth is maximum at the end of the cut with neat diagram.
Identify the true statement from the following a. Unit of cutting speed in millimetre per minute b. Unit of feed is in meter per tooth c. Unit of cutting speed is in meter per second d. Unit of feed is millimetre per tooth
2:(b) “Milling is an intermitted cutting operation”. Explain it.
Two identical cylindrical jobs are turned using (a) a round nosed tool of nose radius 2 mm and (b) a sharp corner tool having principal cutting edge angle = 45° and auxiliary cutting edge angle = 10° If the operation is carried out of the teed of 0.08 mm/rev will Find the height at micro irregularities on the machined surfaces (in mm) in the two cases.
A gear that has a pitch diameter of 6 in. has a diametral pitch of 4. What number of form cutterwould be used in cutting it?