Answered: From the following Identify cutting…

Engineering

Mechanical Engineering

From the following Identify cutting tool made by forging before hardening and grinding. O a. O b. Ос. d.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter23: Fabricating Techniques And Practices

Section: Chapter Questions

Problem 25R: What can happen if a grinding stone with a lower-rated RPM than the grinder is used?

See similar textbooks

Related questions

Q: 11. Two cutting tools with tool life equations given below are being compared: Tool 1: VTº-1-150…

Q: 1.To mill material having a cutting speed of 40 fpm. What should be the RPM of 1.25 inches diameter…

A: Velocity, V= πDN12, where, V= Velocity in fpmD= Diameter in inches (12 is divided in the above…

Q: What is the cutting speed of turning in the unit of m/min, when main axis spindle speed is 2,409 rpm…

A: Given Data N=2409 rpm D=86 mm

Q: Find the commercial tap drill size for 1⁄2”-20

A: given: Find the commercial tap drill size for 1⁄2”-20 NF bolt.

Q: The tool has only one cutting edge and the cutting edge is made of high-grade material like carbide…

A: As per given question The tool has only one cutting edge and the cutting edge is made of high-grade…

Q: A workpiece from AISI 1020 steel will be produced by machining on a lathe. The recommended cutting…

A: Machining is a material removal process in which unwanted material is removed in the form of chips…

Q: Q4 Tool life of a turning tool is given by VTO.12xx=C_at a cutting speed (V) of 25m/min, feed(f)…

Q: Name the following cutters and its function.

Q: Step boring is advised to be used for: Machining hard materials O Machining large radial depth of…

A: Various types of machining operations used are: Turning Boring Drilling Step boring Counter boring…

Q: Q.34 The correct sequence of machining operations to be performed to finish a large diameter through…

A: Our objective is to get a large hole from small hole using machining operation, to get the results…

Q: Prob.1. A broach is used to cut a keyway 8 mm wide, 5 mm deep in a box 64 mm long. Determine – | (i)…

A: Given data: The width of the keyway is w = 8 mm. The depth of the keyway is d = 5 mm. The length of…

Q: A 1 Discontinuous Chips 2 Chemical stability or inertness 3 Planning Continuous chips Seat broaching…

Q: The Taylor's tool life component is 0.3 and constant is 120 for a cutting tool A and 0.5 and 30 for…

A: Given:nA=0.3CA=120nB=0.5CB=30

Q: Calculate the spindle speed (rpm) for turning operation when the cutting speed is 186.00 m/min and…

A: Find the spindle speed Cutting speed = 186 m/sec External diameter = 38.50 mm

Q: 15) In Ultrasonic Machining, the tool oscillation angle in the work piece is: A) Zeroº. B) 45⁰. E)…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: thickness is HW3.A block of steel has a length L-600mm and a width W-450mm. The Machined 10mm, once…

Q: - Formula for finding the correct tap drill size. o for English system o for Metric system - Cutting…

A: Please find the solution below

Q: 26. When a two-fluted end mill is used to cut a slot, the maximum depth of cut should be Select one:…

A: Option a is correct.

Q: Different metals have different CS recommendations. For this question you are considering brass…

A: Answer: The 8 spindle speeds are listed below: N1 = 347.25 rpm. N2 = 401.23 rpm. N3 = 463.62 rpm. N4…

Q: B/ A rectangular aluminum block is drilled at a depth of 40 mm using a drill that has two cutting…

Q: Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a…

A: Given data Mill diameter (d) = 14 mm = 14 x 10-3 m Cutting speed (v) = 16 m/min

Q: For the icon shown in the table name the tool and mention its function from Creo parametric а. b. c.…

A: the bold letters are the tool name and the remaining are its functions as follows (a)component…

Q: The figure shows operation of drilling machine Tool feeds O a. Drilling O b. Boring O c. Reaming O…

Q: 1. List the operations and the tools needed to make the following shape. 2. Find the speed of…

A: 1. operations and the tools needed to make the following shape are listed below:

Q: Drilling is usually performed with a rotating cylindrical tool that has .. cutting edges * O Two O…

Q: In a sharper the cutting tool has a stroke of 16 in. the cutting stroke takes twice the time…

Q: Identify the type of milling operation in which the cutter axis is perpendicular to the workpiece…

A: Milling operation in which the cutter axis is perpendicular to the workpiece being machine

Q: In cylindrical grinding ported by of A. two centers B. a chuc The of a bonded abra

A: Cylindrical grinders are most commonly used for producing accurate shapes and finishing materials…

Q: A cutting tool has a radius of 1.8 mm. The feed rate for a theoretical surface roughness of is 5 Hm…

A: The nose radius of the tool is given as, R=1.8 mm. Now convert the units of surface roughness from…

Q: a. If rough milling of mild steel is performed using High Speed Steel (HSS) side and face milling…

A: Since you have asked multiple questions so we will solve any one of themIf you want any specified…

Q: Which of the following infomation about broaching is wrong?(Broşlama ile ilgili aşa The heights of…

A: Solution: Option A is wrong since the height of the teeth increases over the length of the tool.…

Q: Plunge turning is most suited for: a/ Rough grooving when the depth is bigger than the width…

Q: Tap terms - Sizes of taps - Selecting tap drill size - Formula for finding the correct tap drill…

A: TAPS IN DRILLING - Generally tapping is the process of cutting threads on the inside surface of a…

Q: Penny's duty 1: If you know that n = 0.5 and C = 90, using Taylor's equation, find the percentage…

A: (i) To find : The percentage increase in the life of the cutting tool when the cutting speed…

Q: L the Cutting edges on both the end and outside periphery of the In cutter. * Down milling Face…

A: Ans) : Face Milling

Q: is the lathe operation, which is performed without the cutting tool moving parallel to the axis of…

A: Lathe is a machine tool which is used in the work shop to perform the various machining operations…

Q: From the following Identify cutting tool formed by grinding the end piece of a steel stock is O a. O…

Q: A-List the characteristics of screw thread. B- Calculate the change gears for cutting 16 thread per…

A: Screw threads are shortened threads which are available in helical structure. These threads are…

Q: Identify the name of the milling machine operation in which the cutting takes place by both the end…

Q: Identify the true statement from the following a. Unit of cutting speed in millimetre per minute b.…

A: There are various terms related to the machining operations, such as cutting speed, feed rate, depth…

Q: Calculate the spindle speed (rpm) for turning operation when the cutting speed is 107.00 m/min and…

Q: 14. Determine the proper RPM for a 3" piece of cold-rolled steel with a cutting speed of SFPM. Round…

A: We will answer the first question since the exact one was not specified. Please submit a question…

Q: Which of the following statements is true for climb milling? O used for milling small and intricate…

A: In climb milling the cutting motion of the tool and feeding of work in the same direction, it is…

Q: Identify the operations from the figure Turning Facing Chamfering O drilling

A: Facing process remove the material along diameter.

Q: Identify the tool shown below.

Q: From the following Identify cutting tool that has the cutting edge in the form of small tip made of…

A: Let us discuss about about given single point cutting tool

Q: Milling is an intermitted cutting operation”. Explain it.

A: A milling machine is a machine tool that cuts metal as the workpiece is fed against a rotating…

Q: In a machining operation, doubling the cutting speed reduces the tool life to 1/8th of the original…

A: Given:Taylor's tool life equation,VTn=C

Q: late the machining time to drill the flange as shown below. Take cutting speed 20 m/min, feed for 20…

A: Soln:- depth = 20 mm Number of Revolution required = depth/feed = 20/ 0.2 = 100 rev. V=…

Concept explainers

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.

Question

From the following Identify cutting tool made by
forging before hardening and grinding.
O a.
Ob.
d.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the commercial tap drill size for 1⁄2”-20 NF bolt.
During turning tests, using a cemented carbide tool resulted in a 1‑min tool life at a cutting speed = 4.8 m/s and a 22‑min tool life at a speed = 2.0 m/s. (a) Find the n and C
Identify the name of the milling machine operation in which the cutting takes place by both the end face and periphery of the cutter body. Face milling Slab Milling Peripheral milling End milling
Many of the cutters used in machining are made of either __________________ or ____________________.
Explain elaborately the complete procedure for Grinding Lathe Tool Bits.
A gear that has a pitch diameter of 6 in. has a diametral pitch of 4. What number of form cutterwould be used in cutting it?
In CNC lathes, to maintain constant cutting speed when feeding of the tool from the circumference to the center of the workpiece, the spindle speed (n) is needed to be: a/Increased b/Decreased c/Maintained the same
Specify cutting tool angles for a single-point cutting tool and usage of each angle with aid of aclear sketch.
Identify the type of milling operation in which the cutter axis is perpendicular to the workpiece being machined. face milling angular milling straddle milling gang milling
Using the formula (below), calculate the revolutions per minute (rpm) a drill press spindle should rotate using a Ø1⁄2 HSS twist drill if the cutting speed will be 90 surface feet per minute, SPM?N~[4xV]÷DN = _____________________________________________ RPM’s
What is the stroke per minute of a mild steel which cutting speed is 200 fpm having a total length of 16".
). Explain any three parts of a milling machine. b) Explain the following Lathe operations with a neat diagram. i) Face grooving ii) Parting off c) Explain the following drilling machine operations with a neat diagram. i) Counter boring ii) Gun drilling