From the speed chart below, determine the correct cutting speed for turning a 0.3 in. diameter Alloy Steel shaft on a lathe Surface Speed (Ft/Min) 400 Aluminum 300 Brass/Bronze Low Carbon Steel Cast Iron Alloy Steel 200 100 80 70 60 50 40 Diameter (in) N WAGON 80 2 10 0.8 0.6 0.5 0.4 0.3 0.2 0.1 Cutting Speed (RPM) 10 20 30 -40 50 60 70 80 100 200 300 400 500 600 700 800 1000 2000 3000 4000 - 5000 6000 7000 8000 10000

From the speed chart below, determine the correct cutting speed for turning a 0.3 in. diameter Alloy Steel shaft on a lathe Surface Speed (Ft/Min) 400 Aluminum 300 Brass/Bronze Low Carbon Steel Cast Iron Alloy Steel 200 100 80 70 60 50 40 Diameter (in) N WAGON 80 2 10 0.8 0.6 0.5 0.4 0.3 0.2 0.1 Cutting Speed (RPM) 10 20 30 -40 50 60 70 80 100 200 300 400 500 600 700 800 1000 2000 3000 4000 - 5000 6000 7000 8000 10000

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2 1.60 For a turning operation using a ceramic cutting tool, if the speed is increased by 50% , by what factor must the feed rate be modified to obtain a constant tool life? Use n = 0.5 and y = 0.6.
A part to be turned in an engine lathe must have a surface finish of 1.6 μm. The part is made of a free machining aluminum alloy. Cutting speed = 150 m/min. The nose radius on the tool = 0.75 mm. Determine the feed that will achieve the specified surface finish.
A turning operation is carried out on aluminum. Based on the specific energy values in the table in your text, determine material removal rate and cutting power in the operation under the following sets of conditions: (a) Cutting speed = 5.6 m/s, feed = 0.25 mm/rev, and depth of cut = 2.0 mm; and (b) cutting speed = 1.3 m/s, feed = 0.75 mm/rev, and depth of cut = 4.0 mm.
A student is using a lathe with 80-hp and 80% efficiency to fabricate a copper alloy with Sy = 1200ksi If the width of cut is 0.30 inand the student set a rake angle of 0and a cutting speed of 200fl / min while she assumed a coefficient of friction to be 0.5. What is the maximum depth of cut the student can achieve?
In a turning operation, cutting speed =200 m/min; feed = 0.25mm mm/rev, and depth of cut = 4.00mm Thermal diffusivity of the work material = 20m mm^2/s and volumetric specific heat =3.5(10^ -3 )J/mm^ 3 -C If the temperature increase above ambient temperature (20degreesC) is the angle measured by a tool-chip thermocouple to be 700degreesC, determine the specific energy for the work material in this operation.
In a turning operation, the tool life varies with cutting speed, as shown in following table:Cutting speed, V, m/min Tool life, T, min25 3070 2 Estimate the tool life for this operation at a speed of 60 m/min.
For turning operation, using the table below, find an approximate value for the required speed of rotation of the chuck, in rpm, if the cutting speed for the material 5417 mm/s and the radius of the wp is 0.01 m. Show details of your answer. n | we| o
(j) In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 250 m/min, feed = 0.3 mm/rev, and depth of cut = 8 mm. How much power will the lathe draw in performing this operation if its mechanical efficiency = 95%. Use Table below to obtain the appropriate specific energy value.
A student is using a lathe with 80-hp and 80% efficiency to fabricate a copper alloy with Sy= 1200 ksi. If the width of cut is 0.30 in. and the student set a rake angle of 0° and a cutting speed of 200 ft/ min while she assumed a coefficient of friction to be 0.5. What is the maximum depth of cut the student can achieve?
A drilling operation is to be carried out with a 12.7mm diameter twist drill in a steel work part.The hole is a blind hole of 50mm depth. The cutting speed is 25mm/min and the feed is 0.3mm/rev Determine the following i)Cutting time to complete the driling ii)Metal removal rate
22.31 Do you think that there is a relationship between the cost of a cutting tool and its hot hardness? Explain.
2 1.34 Describe the consequences of exceeding the allowable wear and (Table 21.4) for various cutting-tool materials.