gee-1 50 OTD/D 7,000 1 75 F1,000 ft For ihe 1D, block-centered grid shown in Fig. determine the pressure distribution during the first year of produc- tion. Thee initial reservoir pressure is 6.0o00 psia. The rook and fluid properties for this problem are Ax- 1,000 1, Ay-1,000 ft, Az=75 ft, B 1 RB/STB, G -3.5 x 1O psi 1, ke - 15 md, 0.18, ce, - 10 ep, and B; -1 RB/STB. Use timestep sizes of At- 10, 15, and 30 days. Assume B acts as a constant within the pressure range of interest. L= 5000 loob grid Pressve ds tulaition after 1 yer wing at= 10 days- find 200 -100 95= -150 9 100

gee-1 50 OTD/D 7,000 1 75 F1,000 ft For ihe 1D, block-centered grid shown in Fig. determine the pressure distribution during the first year of produc- tion. Thee initial reservoir pressure is 6.0o00 psia. The rook and fluid properties for this problem are Ax- 1,000 1, Ay-1,000 ft, Az=75 ft, B 1 RB/STB, G -3.5 x 1O psi 1, ke - 15 md, 0.18, ce, - 10 ep, and B; -1 RB/STB. Use timestep sizes of At- 10, 15, and 30 days. Assume B acts as a constant within the pressure range of interest. L= 5000 loob grid Pressve ds tulaition after 1 yer wing at= 10 days- find 200 -100 95= -150 9 100

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the minimum surface tension of a fluid that can sustain a gauge pressure of 0.1 kPa in a 0.5 cm radius bubble?
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
A pitot-static probe will be used to measure the velocitydistribution in a water tunnel at 20°C. The two pressurelines from the probe will be connected to a U-tube manometerthat uses a liquid of specifi c gravity 1.7. The maximumvelocity expected in the water tunnel is 2.3 m/s. Your job isto select an appropriate U-tube from a manufacturer thatsupplies manometers of heights 8, 12, 16, 24, and 36 in.The cost increases signifi cantly with manometer height.Which of these should you purchase?
pllllzzzz help me right nowww plzzz The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
The belt in the Ögure moves at steady velocity V and skims the top of a tank of oil having viscosity. (a) Develop and expression for the required belt drive power in terms of h, L, b, V , and . Recalthat, for steady motion, power is equal to force velocity.(b) What power is required if the belt moves at 5 m/s over SAE 50W oil ( = 0:86 kg/ms) withh = 2 cm, L = 2 m, and b = 0:5 m
Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate for water at 20°C if W = 0.5 mm.
Very small pressure differences p A -p B can be measuredaccurately by the two-fluid differential manometerin Fig. . Density ρ 2 is only slightly larger than thatof the upper fluid ρ 1 . Derive an expression for the proportionalitybetween h and p A - p B if the reservoirs arevery large.
A cylindrical disk ofwood weighing 45.0 N and having adiameter of 30.0 cm floats on a cylinderof oil of density 0.850 g /cm3(Fig.). The cylinder of oilis 75.0 cm deep and has a diameterthe same as that of the wood.(a) What is the gauge pressure at thetop of the oil column? (b) Supposenow that someone puts a weightof 83.0 N on top of the wood, butno oil seeps around the edge of thewood. What is the change in pressureat (i) the bottom of the oil and(ii) halfway down in the oil?
A Horizontal Capillary Tube (Radius 10 Um) Con- Tains An Oil/Water Interface. The Pressure In The Oil Phase Is 14.5 Psi (100 KPa). Determine The Pressure In The Water Phase If The Contact Angle Is 30° And The IFT Is 30 Dynes/Cm (30 MN/M).
A compressed air tank is designed to contain 50 standard cubic feet of air when filled to a gaugepressure of 200 atm at an ambient temperature of 70 F. Assume this is an air tank for scubadiving, and that the approximate shape of the tank is a cylinder with circular cross section. The interior volume of the tank is v=0.253 ft^3(a) If the interior length of the cylinder is 1 ft, what would be the inner diameter?(b) It is desired that the air tank be neutrally buoyant when empty. The density of aluminum is2700 kg/m3. If the tank is made of aluminum, what should be the wall thickness in order forit to be neutrally buoyant?
Pressure in a water container can be measured by an open vertical tube. If the expected water rise is about 20cm. What tube diameter is needed to ensure the capillary action is less than 3%?
In a fluid 1 is oil (sg=0.87) and fluid 2is glycerine at 20 degrees Celsius (w=12360N/m cubed) if Patm=98kpa determine the absolute pressure at p1 Here is the diagram in the picture below