How solve do you this 3 part question. This is a 3 part guestionGiven: A steel shaft with an outside Ø = 36 ± 0.2 millimeters.Determine the tolerance on the shaft:O 0.4 TotalO ±0.4O 0.2 TotalGiven: A steel shaft with an outside Ø = 36 ± 0.2 millimeters.Determine the shaft Ø @ MMC:O Ø 36.0O Ø 36.2O Ø 35.8Given: A steel shaft with an outside Ø = 36 ± 0.2 millimeters.Determine the shaft's Ø @ LMC:O Ø 36.0O Ø 36.2O Ø 35.8

Given: The outside diameter of the pipe is given as ϕ=36±0.2 mm

Given: A steel shaft with an outside Ø = 36 + 0.2 millimeters. Determine the tolerance on the shaft: O 0.4 Total ±0.4 O 0.2 Total Given: A steel shaft with an outside Ø = 36 ± 0.2 millimeters. Determine the shaft Ø @ MMC: O Ø 36.0 O Ø 36.2 O Ø 35.8 Given: A steel shaft with an outside Ø = 36 ± 0.2 millimeters. Determine the shaft's Ø @ LMC: O Ø 36.0 O Ø 36.2 O Ø 35.8

Given: A steel shaft with an outside Ø = 36 + 0.2 millimeters. Determine the tolerance on the shaft: O 0.4 Total ±0.4 O 0.2 Total Given: A steel shaft with an outside Ø = 36 ± 0.2 millimeters. Determine the shaft Ø @ MMC: O Ø 36.0 O Ø 36.2 O Ø 35.8 Given: A steel shaft with an outside Ø = 36 ± 0.2 millimeters. Determine the shaft's Ø @ LMC: O Ø 36.0 O Ø 36.2 O Ø 35.8

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine tolerance value and limit dimension of the rod which a diameter is ∅50 mm, according to the g6 limit deviation (∅50H6). es=-15.24 mkm, ei=0.00 mkm. Determine the basic size, tolerance and limit dimensions.
The diameters of shafts with a nominal size of dn = 68 mm must be within limits dmax = 68.045 mm and dmin = 68.015 mm. What are the upper deviation es. the lower deviation ei. and the tolerance Td? es ei Td 1) -0.015 +0.045 0.030 2) +0.045 -0.015 0.060 3) +0.045 +0.015 0.030 4) +0.015 -0.045 0.060
Determine the limits of sizes, tolerances and fundamental deviations for the shaft designated as 40 H8 / f7
Verify if my answers are correct: P =1000 N Q =1300 N C =216000 N.mm
A steel pipe has an inside diameter of d = 350 mm and an outside diameter of D = 158 mm. The length of the pipe is L = 5.0 m. The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter __ mm Inside diameter __ mm Lenght __ mm 3 decimal places standard coefficient of thermal expansion: steel - 11.25x10^-6 / degrees celcius Aluminum - 23x10^-6 / degrees celcius
....A 150-mm diameter shaft supports a load of 12 kN. The shaft runs in a bearing whose length is 1.5 times the shaft diameter. Which of the following is the bearing pressure? Group of answer choices 0.127 MPa 0.296 MPa 0.356 MPa 0.170 MPa
Values are m= 360mm n= 375mm q= 24mm r= 18mm P= 0.6kN
If the shaft and key have the same material what would be the relationship between the length and the diameter of the shaft. Show your solution. a. Lk = 1.18Ds b. Lk = 1.28Ds c. Lk = 1.38Ds d. Lk = 1.48Ds
Problem (14): Determine tolerance value and limit dimension of the rod which a diameter is ∅127 mm, according to the g6 limit deviation (∅127f6). es=-40.64 mm, ei=-66.04 mm. Determine the basic size, tolerance and limit dimensions.
MN = 48 SN = 79 (1&3) with thickness of 7.5mm
engineering tolerance: A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing with an inlet and outlet diameters of 130 and 145 mm, respectively. Both solid shaft and journalbearing require rigidity and alignment with an accuracy of the location. Consider a journal bearinginlet diameter as the basic size. determine 1. the tolerance limits for both the solid steel shaft diameter and the journal bearing inlet diameter2. the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter
Determine the width and thickness of the leaves (in mm) of a leaf spring using the following specifications: Total load = 140 kN; Number of springs supporting the load = 4; Maximum number of leaves = 10; Span of the spring = 1000 mm; Permissible deflection = 80 mm; Modulus of elasticity, E = 200 kN/mm2; and allowable stress in spring material is 600 MPa.