Given the drawing below, the table shows the range of possible produced sizes and 4 optional feature control frames that can be applied to the Ø12 +0.6/0 hole. Provide the tolerances at each possible produced size for each feature control frame application, i.e., for A), B), C) and D). UNITS = MILLIMETERS Ø12*8.6 A A) Ø0.15 M ABC B) |O Ø0.15 ABC C) eØ0.15OABC D) eØ0 M ABC | Optional feature control franmes DIAMETER TOLERANCE ZONES PERMITTED Produced Size, Ø А, ММС B, RFS C, LMC Zero @ MMC 12.0 12.2 12.4 12.6

Given the drawing below, the table shows the range of possible produced sizes and 4 optional feature control frames that can be applied to the Ø12 +0.6/0 hole. Provide the tolerances at each possible produced size for each feature control frame application, i.e., for A), B), C) and D). UNITS = MILLIMETERS Ø12*8.6 A A) Ø0.15 M ABC B) |O Ø0.15 ABC C) eØ0.15OABC D) eØ0 M ABC | Optional feature control franmes DIAMETER TOLERANCE ZONES PERMITTED Produced Size, Ø А, ММС B, RFS C, LMC Zero @ MMC 12.0 12.2 12.4 12.6

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 10RQ: List and briefly describe the three types of tolerances used on prints.

See similar textbooks

Similar questions

1)Meaning of the term "Grade" in a grinding wheel is a. How much spacing between the abrasive grains in the grinding wheel b. The ability of the abrasive grains to hold together to form the grinding wheel c. The strength of the bond inside the grinding wheel d. The abrasive grain size used in grinding wheel production 2)In a Vernier Caliper if the vernier scale with ______________divisions (lines), will be 0.05 mm least count. a. 50 b. 30 c. 20 d. 40
Research and identify one type of geometric tolerances (besides obvious specs like length, distance, diameter, etc.) that can be called out on a technical drawing. Explain how this tolerance is defined
Using the 10% rule–of–thumb for determining gagemaker’s tolerance for a plug gage, determine the GO and NO GO plug diameters for a hole with a dimension of φ1.875 + .003. Identify which is the GO plug and which is the NO GO. Please explain
Two lathes are being considered in the manufacture of certain machine parts. Data is given below, all cost in peso: LATHE A LATHE B First Cost 40,000 56,000 Salvage Value 5,000 7,000 Annual Maintenance 2,000 2,800 Operation, Cost/hour 4 3.5 Life, in years 10 12 Time per part (hours) 0.40 0.25 REQUIRED: If the number of parts is 10,000 units, which lathe will you recommend? Use EUAC please use EUAC
On the part in Q1, show the size and shape of the tolerances zone. Lecture 5 Q1 On the part below, apply position controls to allow the holes to move 0.2mm radially. Include references to datum features A, B and C.
Refer to the 1.914 dimension. A) Where is the tolerance specified ? _________________________________ B) What is its tolerance ? ________________________________C) What is the MMC? ______________________________ D) What is the LMC? _______________________________
Some hole size tolerances are specified as D7, N6, and H8. Where does the print reader find the values for those specifications? (Multiple Choice)a. In a tolerance block located in the upper-left corner of the sheetb. On line at the manufacturers websitec. A supplemental documentd. The are proprietary and not stated
For a floating fastener application, a hole size specification of 385" minimum and .395" maximum diameter has a position tolerance specification of .010" diameter MMC. If the position tolerance is changed to .000" diameter MMC, a minimum hole diameter of must be specified with the maximum size limit remaining .395", A. .375 B. .380 C. .385 D. .390
Given a pin with a size dimension of Ø.875±.003 and a perpendicularity tolerance of .002 at MMC to a primary datum, what is the boundary that takes into consideration the combined effect of feature size at MMC and the geometric tolerance? .870 .874 .876 .880
Based on the CNC program below, identify 1)what machine it is (lathe/mill) ? 2)is the coolant used? 3)Any pocket/holes drilling? and if yes how many? 4)How many tool(s) is/are used? N1 G90 G17 G40 G80 G00 N108 M06 T1 (1/4) N110 (F-contour) N112 G00 G54 G90 X0.8937 Y-2.0181 S6000 M03 N114 G43 H1 Z5. N116 Z1. N118 Z0.1 N120 G01 Z0. F30. N122 G03 X0.9302 Y-2.262 Z-0.0007 I0.2488 J-0.0875 F60. N124 G02 X0.9927 Y-2.4845 Z-0.0012 I-0.2631 J-0.1939 N126 G03 X0.9927 Y-2.7716 Z-0.002 I1.6354 J-0.1436 N128 G02 X0.9302 Y-2.9941 Z-0.0026 I-0.3256 J-0.0286 N130 G03 X0.8937 Y-3.2381 Z-0.0032 I0.2123 J-0.1565 N132 X2.0181 Y-4.3624 Z-0.0074 I1.7344 J0.61 N134 X2.262 Y-4.3259 Z-0.008 I0.0875 J0.2488 N136 G02 X2.4845 Y-4.2634 Z-0.0086 I0.1939 J-0.2631 N138 G03 X2.7716 Y-4.2634 Z-0.0094 I0.1436 J1.6354 N140 G02 X2.9941 Y-4.3259 Z-0.01 I0.0286 J-0.3256 N142 G03 X3.2381 Y-4.3624 Z-0.0106 I0.1565 J0.2123 N144 X4.3624 Y-3.2381 Z-0.0148 I-0.61 J1.7344 N146 X4.3259 Y-2.9941 Z-0.0154 I-0.2488…
a) Determine the limits of sizes, tolerances and fundamental deviations for the shaft designated as 40 H8 / f7 b) Using part reduction method redesign paper punch and calculate the assembly time using Boothroyddewhurst method.
What are the significance of tolerance and allowance in production process? Diagram?