Tolerance note is given by: .XX ± .01 cm and .XXX ± .001 cm. What is the tolerance for a feature with a dimension 3.250 cm? Select one: a. 0.02 O b. 0.001 O c. 0.015 O d. 0.01

Q: The tolerance for a ball bearing is 0.01. if the true diameter of the bearing is be 2.0 inches and…

A: GIVEN  TOLERANCE =0.01 INCH  TRUE DIAMETER OF BEARING IS 2 INCH

Q: If the gage reading at (A) is (pA=1OkPa), find the gage reading at (B) in (Pa) and in (mm Hg)?…

A: Write the given values with suitable variables. PA=10 kPa Consider, a reference line of the…

Q: What type of geometric tolerances have no datum features? Profile Tolerances All Tolerances O…

A: Geometrical Tolerancing: The tolerances in any system which allows tolerances to be applied…

Q: Which option is wrong?         a) A unilateral tolerance allows a dimension to vary ei- ther above…

A: A unilateral tolerance allows the variation either above or below the basic size but not both.…

Q: There are some incorrect indications in the following Fig.2. a) Re-draw a correct indicated drawing…

A:

Q: The following limits are specified in a limit system, to give a clearance fit between a hole and a…

A:

Q: The company produced a new product intended to measure diameter profiles. In a run test conducted,…

A: 1). Precision- option B is correct Accuracy is how close or far off a given set of measurements are…

Q: 22. Fill in the Blanks on the Charts below: Pertains to Individual Feature Only Individual Feature…

A:

Q: Enumerate at least 20 G-CODES and 10 M-CODES and write their description. Create a table to organize…

A: Given question: Enumerate at least 20 G-CODES and 10 M-CODES and write their description G Codes are…

Q: Suppose a dimension is indicated on an engineering drawing (with all units in inches) as 1.658 ±…

A: The lower limit of dimension= 1.658 - 0.008 = 1.650 Option third is correct.    Similarly, we can…

Q: Given the drawing below, answer questions 11, 12 and 13. DIMENSIONS ARE INCHES +.00 3.00 -.03 2.00…

A:

Q: A material condition used to indicate that a specified geometric tolerance applies at each increment…

A:

Q: Question 14 The total amount that the feature on the actual part is allowed to vary from the…

A: Allowance: It is the difference between the basic sizes (difference between the hole diameter and…

Q: Using the 10% rule–of–thumb for determining gagemaker’s tolerance for a plug gage, determinethe GO…

A: Given data: Calculate the maximum hole dimension as follows: Calculate the minimum hole dimension…

Q: 36. (SI units) A GO/NO-GO plug gage will be designed to inspect a 60.00 0.40 mm diameter hole. A…

A:

Q: 2. Form tolerances are independent of all other Features Size Limits Datums ?

A: Form tolerance is a geometric tolerance that defines the roundness, flatess, straightness of a part.

Q: (USCS UNITS) A GO/NO GO PLUG GAUGE WILL BE DESIGNED TO INSPECT A 2.000 +/- 0.002mm DIAMETER HOLE. A…

A: Given data,

Q: Given the following sentence descriptions of the geometric tolerance information, correctly sketch…

A:

Q: 2. The cross-sectional shape of this feature must be round within a radial tolerance zone of .002"

A: To find:  sketch a feature control frame that matches the description given.: 2. The cross-sectional…

Q: Use the prefix multipliers to express cach measurement without any exponents. 22 x 10-15s

A: Given: The time is t=22×10-15 s. The unit conversion factor to convert Second into Femtosecond is, 1…

Q: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact dimension is…

A: As per Bartleby guidelines, this is a multipart question and we will answer the first three…

Q: Identify which is the GO plug and which is the NO GO.   Please explain

A: As per ISO standard design of go-no go gauge will follow as below.for solution refer below images.

Q: Assignment 8.2: Measurements and Tolerances (continued) 11. A toy company manufactures wooden blocks…

A: Consider the side of cube have measure with error of (4.5±0.1)cma. Calculate maximum surface areathe…

Q: Unless otherwise specified, all tolerances and datum features apply for the full Unless otherwise…

A:

Q: M5.19 (Sl units) A GO/NO-GO plug gage will be designed to inspect a 50.00 0.20mm diameter hole.…

A: Calculate the tolerance band.

Q: Given the drawing below, the table shows the range of possible produced sizes and 4 optional feature…

A:

Q: Fill out the table for the shaft-hole assembly Hole Ø 9.12 9.0 Shaft Ø 9.12 8.89 Shaft Hole Limits…

A: Fundamental deviation is the nearest deviation to basic size , It is either lower deviation or upper…

Q: All form tolerances are surface controls except for Form tolerances are independent of all other and

A: Form tolerance is a used to determine the form of the part. It refers to the limitation of a form…

Q: II. Comprehensive questions. 1. Explain the meaning of the following annotations, the tolerance…

A: For solution refer below images.

Q: Given data: Stain=0.00021 Initial length=120 mm Find change in length

A: Given data : Strain=ε Initial length=L   Required : Change in length

Q: Problem 4: Metal sheet paper is cut to a width of 205 cm with a tolerance of +/-05. The cutting…

A: The little positional difference that occurs when sheet metal is cut is known as profile cutting…

Q: 5. When verifying flatness, the feature of size is first measured to verify that it falls within the…

A: given = fill in the blank

Q: 1. What is the philosophy of the Go and No-Go gauging? Explain in some details (need schematics) 2.…

A:

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Which method specifies the tolerance by providing dimensions for the upper and lower limit in place…

A: Definition of Tolerance : Tolerance is the total permissible variation of a size, means it is not…

Q: 31. (USCS units) A GO/NO-GO plug gage will be designed to inspect a 2.000 0.002 mm diameter hole. A…

A: Given data as per questionDimension of object to be inspected =2.000±0.002mmWear allowance…

Q: I need help answering problems 13, 14, and 15 pertaining to the print attatched below.

A: The print sheets attached shows the manufacturing or material part drawing of a mechanical part (her…

Q: how do you write this in a feature control frame? "The cross-sectional shape of this feature must be…

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: 'D' dimension : Basic size Tolerance Max size Min size . 'E' dimension : Max size Min size

A:

Q: Which type of feature doesn't belong to form tolerances?   a)The profile of a surface b)Circularity…

A: Solution:

Q: Using the 10% rule of thumb for determining gagemaker’s tolerance for a plug gage, determine the GO…

A:

Q: M5.20 (Sl units) A GO/NO-GO plug gage will be designed to inspect a 50.00 0.20mm diameter hole.…

A: Go gage will inspect the minimum shaft diameterAnd NO-GO gage will inspect maximum shaft diameter.

Q: a nominal size of 50 mm are as follows: Hole

A:

Q: If you know the value of tolerance Tp and the upper deviation ES, then by what formula is the lower…

A:

Q: V- Micrometers are using to measuring - with high accurate. a) Small dimensions part b) Big…

A: ● Micrometer is a precise measuring instrument for precise and accurate measurements of small parts.…

Q: In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 70…

A: Given: Dimensions of,Hole=70+0.00+0.04mmShaft=70-0.08-0.04mm

Q: Complete the interpretation drawing for the specified tolerances. Add any required tolerance zone…

A: Complete the interpretation drawing for the specified tolerances. Add any required tolerance zone…

Q: What are the tolerance valuesgiven below?1-Ø30 H7, 2-Ø25m6, 3-Ø35h11 Note: Draw the tolerance…

A: Given: Tolerance values, 1-Ø30 H7, 2-Ø25 m6, 3-Ø35 h11,

Theory and Design for Mechanical Measurements

Measurement is a term that refers to analyzing a manufactured component regarding the degree of accuracy for dimensions, tolerances, geometric profile, roundness, flatness, smoothness, etc. Measurement always involves comparing the manufactured component or the prototype with a standard specimen whose dimensions and other parameters are assumed to be perfect and do not undergo changes with respect to time.Precisely in mechanical engineering the branch that deals with the application of scientific principles for measurements is known as metrology. The domain of metrology in general deals with various measurements like mechanical, chemical, thermodynamic, physical, and biological measurements. In mechanical engineering, the measurements are limited to mechanical specific such as length, mass, surface profile, flatness, roundness, viscosity, heat transfer, etc.

Basic principles of engineering metrology

Metrology is described as the science of measurement, precision, and accuracy. In other words, it is a method of measurement based on units and predefined standards.