Given the drawing below, answer questions 11, 12 and 13. DIMENSIONS ARE INCHES +.00 3.00 -.03 2.00 t.02 502 +.000 -.001 K 0.750 .498 11. 'G' dimension : Nominal size Tolerance Маx size Min size 12. 'H' dimension : Nominal size Tolerance Max size Min size Page 13. 'L' dimension : Маx size Min size

Given the drawing below, answer questions 11, 12 and 13. DIMENSIONS ARE INCHES +.00 3.00 -.03 2.00 t.02 502 +.000 -.001 K 0.750 .498 11. 'G' dimension : Nominal size Tolerance Маx size Min size 12. 'H' dimension : Nominal size Tolerance Max size Min size Page 13. 'L' dimension : Маx size Min size

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 9RQ: A dimension listed on an engineering drawing is known as the _______ _______.

See similar textbooks

Similar questions

Suppose you make the following sequence of measurements for the segments in laying out a compressed air line: 4.61 m 211 m 0.500 m What should be the reported total length of the air line? options: 216.1 216.110 220 216.11 216
Similarity, solve for P1 as well
Calculate the answer, and present in scientific notation. (0.32)(14.50)(120)= (14.1)/(0.005)= (3.9)(6.05)(420)=
Five engineers measure the thickness of a slab using a meter stick and a vernier caliper. One engineer got a thickness of 4.3 cm ± 0.1 cm using a meter stick, the other four engineers measured a thickness of (a) 4.32 cm ± 0.01 cm, (b) 4.31 cm ± 0.01 cm, (c) 4.24 cm ± 0.01 cm, and (d) 4.43 cm ± 0.01 cm respectively using the caliper. Which of these four measurements made by the four engineers agree with the measurement obtained by the engineer that used a meter stick? Only a (b) and (c) (c) and (d) (a), (b), and (c) none of these
two cylinders are printed on a 3d printer, with a setting of 40% fill rate. This means that the solid parts of the cylinders at 40% plastic material. Given this, tell me how much plastic material is used to make each of these cylinders. I measured both cylinders in meters and these are the measurements below A) Cylinder 1- Height: 0.042m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m B) Cylinder 2 Height: 0.022m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m
The most powerful engine available for the classic 1963Chevrolet Corvette Sting Ray developed 360 horsepower and had a displacement of 327 cubic inches. Express this displacement in liters (L) by using only the conversions 1 L = 1000 cm3 and1 in. = 2.54 cm.
Hide AnswerTry Another The formula for piston displacement is P = cd2SN, where c is a constant, d is the cylinder bore, S is the stroke, and N is the number of cylinders. For c = 0.7854, d = 3.000, S = 4, and N = 6, find the piston displacement. (Use the rules for working with measurements to give your answer to the appropriate accuracy and/or precision. Note: The values for S and N are exact numbers. Ignore exact numbers when determining the appropriate accuracy and/or precision.)
Type your answer in the space provided after each item. Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40) If your answer is 120.00 kN, just write 120 kN Do not round off values during solving. Use the store function of your calculator or its fraction if applicable. Include the units after your answer. Leave a space between the value and the unit. (ex: 6323.17 m, 73.10 rad/s^2, 100 kN, 12.90 mm^2, 120 lbs) There is no period after the unit.
A dimension listed on an engineering drawing is known as the _______ _______.
(SI Units) In a tensile test, the starting gage length = 100.0 mm and the cross-sectional area = 150 mm2. During testing, the following force and gage length data are collected: (1) 17,790 N at 100.2 mm, (2) 23,040 N at 103.5 mm, (3) 27,370 N at 110.5 mm, (4) 28,910 N at 122.0 mm, (5) 27,480 N at 130.0 mm, and (6) 20,460 N at 135.1 mm. The final data point (6) occurred immediately prior to failure. Yielding occurred at a load of 19,390 N (0.2% offset value), and the maximum load (4) was 28,960 N. (a) Plot the engineering stress strain curve. Determine (b) yield strength, (c) modulus of elasticity, (d) tensile strength, and (e) percent elongation.
Using only Table A (Conversion of Units), calculate the values asked. All answers must be given with the primary dimensions and units of the SI system. 1.907ft3 of a substance has a specific volume of 802.5 L/slug , determine the absolute volume
On your new small car, you replace the factory-installed P185/75R14 tires with slightly larger P205/75R14 tires. Find the missing number in each statement: Show all of your work. P185/75R14 (Old) P205/75R14 (New) Width(mm) Aspect Ratio (%) Height (in.) Diameter (in)