Given the volume of 0.1416 M NaOH used determine the concentration of 16 ml sample each from aquaeous layer (Aq) and benzene layer (Or). To reach the end point of Aquqeous layer and organic layer 13.16 ml and 14.00 ml of NaOH used respectively using Phenolppthalein indicator. What will be the Kd of the system?

Given the volume of 0.1416 M NaOH used determine the concentration of 16 ml sample each from aquaeous layer (Aq) and benzene layer (Or). To reach the end point of Aquqeous layer and organic layer 13.16 ml and 14.00 ml of NaOH used respectively using Phenolppthalein indicator. What will be the Kd of the system?

Chemistry: Principles and Practice

3rd Edition

ISBN:9780534420123

Author:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Publisher:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Chapter16: Reactions Between Acids And Bases

Section: Chapter Questions

Problem 16.54QE

See similar textbooks

Similar questions

Why does the color change of an indicator take place over arange of about 2 pH units?
A student titrates a 50.00mL sample of water with 17.85mL of 0.0100M ethylenediaminetetraacetic acid at pH = 10 to the Erio T indicator end point. What is the hardness of the water sample in ppm CaCO3 (Molar mass = 100.1 g/mol)?
T or F: The normality of the solution obtained by dissolving the acid sample be approximately the same as that of the titrant.
A 25.00-mL sample of vinegar is diluted with deionized to 100.0 mL. Then a 10.00-mL aliquot (portion) of the dilute vinegar solutionis titrated with 0.1055MNaOHsolution using phenolphthalein as theindicator. (a) If 19.60mL of the base solution is required to reach the end-point, calculate the molar concentration of acetic in dilute vinegar solution. (b) What is the molar concentration of acetic acid in the original (undiluted) vinegar? At the end-point, the volume of NaOH consumed was found to be 32.00 mL. The acid-base reaction occurs as follows: HC2H3O2(aq) + NaOH(aq) --> H2O(l) + NaC2H3O2(aq)
While preparing the samples for analysis, you forgot that you already added phenolphthalein indicator so you added some more. What will be its effect in the volume of the titrant needed to reach the endpoint? Select one: A. Increase B. Decrease C. No effect D. Cannot be determined Primary standards are used to determine the exact concentration of the titrant. Based on the criteria of primary standards, which of the following cannot be used as a primary standard? Select one: A.Oxalic acid B. Sodium hydroxide C. Sodium carbonate D. Potassium dichromate During titration, you notice that the retention of the faint pink color is longer than earlier. Your lab partner suggested that you add a “half-drop” to prevent over-titration of the analyte solution. Is it ethical to do the “half-drop” technique? Select one: A. NO. It will cause error in calculations if you forgot to record the volume reading before adding the half-drop. B. YES. No error in calculations will be encountered provided…
Could a Conductimetric Titration of a Barium Hydroxide Solution be performed using Hydrochloric Acid ? Explain why or why not.
Advantages of potentiometric titrations over 'classical' visual indicator methods: (select the correct statement(s)). Can be used for colored, turbid or fluorescent analyte solution. Can be used if there is no suitable indicator or if the color change is difficult to visualize. Both answers 1 and 2 are correct
Define pH indicator. The amount of pH indicator added are normally kept as small aspossible in a titration process. Explain on the reason why we should not add excessive pHindicator into sample during titration.
Create a schemantic diagram of qualitative analysis for CoCO3.
For the analysis of a 50 mL sample consisting of carbonate mixtures, when the phenolphthalein indicator is added and titrated with 0.1 M HCl, 10 ml of acid is consumed until the turning point. Since the bromocresol indicator is added after the first turning point and 15 mL of HCl acid is added, find the number of moles in the initial solution..
A 4.0520g sample of HCl, specific Gravity 11.18, required 44.15ml of 0.9035M of Sodium Hydroxide in titration, compute for percent purity. Please explain thoroughly. I have an answer of more than 100% concentration and I'm not sure I just want to double check. Thank you and have a great day.
Na2CO3 served as the primary standard in a titration experiment. Find the molarity of the titrant given the following data in 3 decimal places. Show solutions Primary Standard Used: Na2CO3Formula Mass of 1º standard: 105.99 g/mol% purity of 1º standard: 95% Trial 1 2 3 1º Standard weight, g 0.1005 0.1001 0.0997 Net volume of HCl, mL 9.30 9.00 8.90 Molarity of HCl X1 X2 X3