he wheel is subjected to a torque of M-55 N-m. The oefficient of kinetic friction between the band brake and the rim of the wheel is 0.3 (Figure 1) Part A Determine the smallest horizontal force P that must be applied to the lever to stop the wheel Express your answer to three significant figures and include the appropriate units.

he wheel is subjected to a torque of M-55 N-m. The oefficient of kinetic friction between the band brake and the rim of the wheel is 0.3 (Figure 1) Part A Determine the smallest horizontal force P that must be applied to the lever to stop the wheel Express your answer to three significant figures and include the appropriate units.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
load of Ft = 700 N comes to the free wheel of a car. The coefficient of friction between road and tire is µT = 0.8. Wheel radius is twice the disc friction radius (Rt = 2 Rs), µ = 0.35 between pad and disc and allowable pressure p = 0.5 N/mm2 Determine the pad sizes
1. A 5.0kg steel block is resting on a horizontal table. The coefficient of static friction is 0.75 and coeficient of kinetic friction is 0.57. What is the maximum force that can be applied horizontally before it starts to move? 2. Three drums stacked as shown. Considering the weight of the drums and friction in all contact surfaces, how many forces are there in the FBD of A? (Friction and normal forces are treated separately.) (*see first image for the figure) 3. How many components (forces and couples) does a fixed support in 3D contain? (*see second image for the figure)
A load of Ft = 700 N comes to the free wheel of a car. The coefficient of friction between road and tire is µT = 0.8. Wheel radius is twice the disc friction radius (Rt = 2 Rs), µ = 0.35 between pad and disc and allowable pressure p = 0.5 N/mm2 Determine the pad sizes and the hydraulic pressure that should be sent to the piston. Piston's diameter is d = 30 mm.
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
A block brake with a torque of 250 N-m. Its drum rotates at 100 rpm. The length of the block (1) is twice its width (w). Assume, the coefficient of friction P is 0.35. Calculate: (1) the applied load (P) and the hinge-pin reaction (Rx ana Ry) for clockwise rotation of the drum; (2) the applied load and hinge-pin reaction for anticlockwise rotation of the drum; (3) the rate of heat generated during the braking action. (4) The dimensions of the block, if the intensity of pressure between the block and brake drum is 1 MPa. (5) Check whether the brake is self-locking.
Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of friction between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm2.
An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the corresponding angles of lap are 160° and 210°. The smaller pulley runs at 200 r.p.m. The coefficient of friction between the belt and pulley is 0.25. It is found that the belt is on the point of slipping when 3 kW is transmitted. To increase the power transmitted two alternatives are suggested, namely (i) increasing the initial tension by 10%, and (ii) increasing the coefficient of friction by 10% by the application of a suitable dressing to the belt. Which of these two methods would be more effective? Find the percentage increase in power possible in each case.
A single block brake is shown in the figure. The diameter of the drum is 250 mm and the angle of contact is 103.7°. If the operating force of 661N is applied at the end of a lever and the coefficient of friction between the drum and the lining is 0.35, determine: a. The tangential braking force, Ft, in Newtons b. The braking the torque transmitted by the block brake in N-m.
The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.3; working speed= 600 rpm; friction surface number= 2; If required clamping force = 2917 N, clutch outer diameter = 400 mm, clutch inner diameter = 160 mm, what is the transmitted power?
For the same question, the Impeller hub will be pressed onto the taper shaft with the Nut. How much FORCE should the nut create for this? Also, if the nut loosens and falls off, calculate whether the connection will be DISCONNECTED by itself. (Do not take the values from the previous question, use the values given in this question!) Engine power P=27 kW, RPM n=1684 rpm, Connection MEDIUM vibrating, Conical inclination angle α=1, Coefficient of Friction μ=0.3 , Average of the conical part diameter d=24 mm, connection width b=96 mm
A single disc clutch with both sides effective is required for a vehicle. The power for initial estimation of the clutch is 100 kW at 4000 rpm. Determine the radial dimensions (inner and outer radius) and the actuating force (W). Base the design on the uniform wear assumption. Assume maximum pressure (pmax) as 1.6 MN/m2 and ?2?1= 1√2where ‘r2’ and ‘r1’ represent inner and outer radius of the friction surface. Take µ = 0.35. Find also the minimum pressure (pmin).