to : 4) Horizontal component of pinch force tries Cause the arc blow Reduce the cross-section of the molten drop Cause the rotational transfer of molten metal Make the molten metal drop of big size

Q: I, Give the FBD for OA and whole system. A В M

A: Free body diagram of the member OA is ROH and ROV are the horizontal and vertical reaction forces…

Q: Draw the complete Ts diagram of the given process

A:

Q: Derive the Steady Flow Energy Equation from the first principles

A: Consider a steady flow device as shown below where one stream of fluid enters and other leaves the…

Q: create Mind Map for Normalizing (heat treatment process)

A: Normalizing is a heat treatment process, heating a material above the recrystallization temperature…

Q: n, how much does it cost to run the air per month (30 days)?

A: To find total cost

Q: ed like a long semi- c of the dryer is oc ure to be dried. The ure of 500°C, while

A: given:diameter D=2mT1=400cT2=5000c

Q: takes minimal effort to recognize where energy can be saved. However, it takes cond efforts to…

A: Working principle of lobe compressor A gear with a narrow clearance but no metal-to-metal contact…

Q: The work ratio of a gas turbine plant is given by

A:

Q: Furnace is operating at 200K and is produce a heat of 3000 KJ to a sink at 150K and 630K. Which sink…

A: Given data: Furnace operating temperature, Tf = 200 K. Sink-1 temperature, Ts1 = 150 K. Sink-2…

Q: pot

A:

Q: 3- Discuss the siphon process and what benefit of it?

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Calculate work done for the isothermal process.

A: For isothermal process PV =constant

Q: A small steam turbine power plant of 5000 kw capacity has a full load steam rate of 6 kg steam per…

A:

Q: 7) On increasing the current value in SMAW process

A: Solution:

Q: lled purposely to cool us available at the rate

A: The heat transfer between two things is proportional to the temperature differential between them.…

Q: Ag. Bys Find the reactions. Fill in the blank's. 8k. a 4' 6' 6. FBD Final FBD

A:

Q: The available energy

A: Given; A steel billet of,m=2000kgT1=1250 KT2=450 KAmbient temperature,ta=303 KSpecific heat of…

Q: Describe the Mass and Volume Flow Rates?

A: Mass flow rate is the mass of fluid crossing a cross-section area per unit time. If a density of the…

Q: Reheat cycle then solve for it

A: given; Reheat cycle then solve for it

Q: The most economical process

A: Given, A component can be produced by any of the four processes. Fixed cost and the variable cost is…

Q: Project 2 You are an engineer working in a factory that produce heavy machines, one of the…

A: Task 1  The system parameters using the Non-Flow Energy Equation Non-Flow Energy Equation : It is…

Q: Isothermal process is the best for production of maximum work for all working fluids. False True

A: As we know there are various thermodynamic processes such as isobaric process, isochoric process,…

Q: 5W 4W 8W 8W 2a 2a

A: given simply supported beam as shown below

Q: Air is used as a working substance in a given internal combustion engine, which is supplied with…

A:

Q: To 212 F Water at 65 F flows nto a boiler at 5 gal min. It is converted to steam at 212 F Find the…

A: Given Data State 1: Saturated water, 65°F State 2: Steam, 212°F V= 5 gal/min

Q: The thermal

A: Given: Heat engine recieves heat:Q1=35 KJT1=750CRejects heat to the ambient is:Q2=15 KJT2=280C

Q: Find Qai Qri Whet, and the efficiency·

A: Given that: The cycle is a Carnot cycle. Working fluid is air. Maximum temperature = 500 K. Minimum…

Q: a) Total expansion work (kJ/kg) b) Intermediate heating amount (kJ/kg) c) Calculate the rate of…

A: For solution refer below images.

Q: Q3: What are the priority operations for minimization and recycling of waste

A: Basically Waste is unwanted or which unusable and which provides harm to the environment. So it is…

Q: Superheating is beneficial as it

A: As per the guidelines of company we are subjected to solve only one question at a time. please…

Q: D. Draw the complete Ts diagram of the given process.

A:

Q: g an energy atte the 1200 kg ca

A: K. E. =  1/2 mv^2   K.E. =  1/2 *1200*100*100 K.E. = 12000000 j   or 1200KJ

Q: A Bys Find the reactions. Fill in the blank's. 8k a 4' 6' 6. FBD

A:

Q: efficiency and pres Explain each of the processes on the T-s diagram.

A: Given: Gas turbine cycle Describe the processes.

Q: _is the amount of heat transferred to water to produce the required quantity of steam Quality of…

A: Quality of steam is nothing but dryness fraction. Quantity of steam is the amount produced in kg.

Q: room is heated by an iron that is left plugged in. Is this a heat or work injection? Take the entire…

A: It is required to evaluate given statement

Q: the latent heat represents

A: This question is based on the concept of latent heat of vaporization from thermodynamics.

Q: Write the steps to produce the pig iron.

A: Pig Iron: 1.The name pig iron originated in the early days of iron ore reduction when the total…

Q: here the temperature is use where the tempera ults in infiltration even

A:

Q: below? [5]

A:

Q: Write the name of the law relates with isothermal process

A: Isothermal process is that process in which temperature remains constant.

Q: relocity in

A:

Q: Calculate isothermal efficiency, power required to

A: To find  isothermal efficiency Power required

Q: Air is used as a working substance in a given internal combustion engine, which is supplied with…

A: Answer: The work of the cycle is 660.316 kJ/kg.

Q: o 350 °C. Sketch a diagram to required heat input in J/s if a onstant pressure.

A: Given that ,  T1=100°CT2=350°Cm˙=100kg/s

Q: For the pot shown in figure (ignore stand): a. Name all possible processes by which it can be…

A: a. The  possible processes by which it can be manufactured is  1. Deep Drawing 2. Ironing  3.…

Q: can you calculate also the diameter of stack

A: Given      Density of gas = 0.7756 kg/m3                 Draft, h = 56.954 m     Mass of fuel, m =…

Q: The rated boiler horsepower of a fire tube boiler is 500 Hp. What is the heating surface area of the…

A:

Q: 15. Define with sketch the Hot-chamber machines

A: Given :- Hot chamber machines

Q: When the work done is zero?

A: Work: In thermodynamics, When Energy is transferred by the system to its surroundings  then work is…