The tool used for cutting the sheet metal after marking is called snips. Select one: O True False

Q: 50. The movement of the cutter of the shaping machine over the work is called Select one: a.COURSE…

A: Course is a term associated with feed. Crank is a rotating link of the shaper mechanism.  Travel is…

Q: show FBD

A: As per question asked below is the FBD of the given problem

Q: The positive rake angle in a single point cutting tool is used to cut non-ferrous metals and low…

A: Positive rake angle is provided to low strength material, to reduce BUE, for low speed operation

Q: Clue 6 in. the

A: The given conditions are: The thickness of the wooden plank is 78 inch. Average shearing stress =…

Q: 12. The tool used to shear the metal together with the use of hammer is called Select one: а.НАСKSAW…

A: Chisel, a cutting tool with a sharp edge at the end of a metal blade, used—often by means of a…

Q: the normal and shearing

A: To determine the normal and shear stress .

Q: Sheet No.2 1- Write a program to find the average of 50 numbers and print the result.

A: Question (1) is Solved here. For Other Question, please Post again.

Q: Up milling operation is performed for finishing cut. Select one: True O False

A: Down milling is performed for finishing and get smooth surface.

Q: The correct words for the blanks are

A: Given; In case of tubulent flow of a fluid flow through a circular tube. Where,  Turbulent flow is a…

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: Draw a neat

A:

Q: The following tool is used to cutting internal threads of drilled hole Select one: a. Drill plate b.…

A: It is required to which tool is used to cutting internal thread of drilled hole

Q: Up milling operation is performed for finishing cut. Select one: True False

A:

Q: In a lathe machine tool, when the cutting tool moves perpendicular to the axis of rotation of the…

A: The given statement is ,

Q: In a lathe machine tool, when the cutting tool moves parallel to the axis of rotation of the…

A: It is required to justify given statement

Q: • Sliting is the operation of: Removal of metal to the desired shape from the edge of a plate.…

A: Slitting is a sheet metal cutting operation carried on the sheets of the metal by using circular…

Q: In a lathe machine tool, when the cutting tool moves perpendicular to the axis of rotation of the…

A: True

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: The figure shows operation of drilling machine Tool feeds O a. Drilling O b. Boring O c. Reaming O…

A:

Q: From the following Identify cutting tool formed by grinding the end piece of a steel stock is O a. O…

A: Option d is correct.

Q: True or False: The BREAK command requires two separate points when breaking a circle.

A: The BREAK command is used to break the selected object between two points.

Q: Which of the following is the correct order of doing a fitting Job C. Marking -Filing - Surface…

A: First step of fitting job is marking then we can clamp the object in the vice so that material…

Q: When the cutting tool is feed parallel to the rotation of the workpiece in a lathe, the following…

A:

Q: In a tap set, a plug tap is used for final cutting the thread throughout its length after using two…

A: Solution:

Q: The deep drawing blankholder is used in order to avoid defects of the flange which are named O a.…

A: b. The deep drawing blank holder is used to avoid wrinkling defect

Q: MATCH THE ANSWER WITH THE QUESTION

A: Given:

Q: Which of the following process for sheet metal cutting, the cut piece is the desired part? Shearing…

A:

Q: The tool used for marking center is __________. a.   Steel rule   b.   Divider   c.…

A: Solution:

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: Hanf written plzzz asap.plzz i'll rate sure

A:

Q: In drilling operations, drill chucks are used for holding the work piece. Select one: True False

A: The above statement is false

Q: 50. The movement of the cutter of the shaping machine over the work is called Select one: a.COURSE…

A: Generally shaping machine has two strokes they are 1. Cutting stroke or forward stroke 2. return…

Q: Identify the cutting tool from the following File V block Punch Angle plate

A: 1) v-block  V-Blocks are precision metalworking jigs typically used to hold round metal rods or…

Q: °C. What is the distance of zero and 30 mark under these conditions?

A:

Q: The answer should be 24,6kN when rounded up.

A:

Q: The thickness of the blank

A: Given; Determine thickness of the blank needed to produce; by power spinning a missile cone of…

Q: Which one(s) of the following statements is true for limiting positions? Select all that apply.

A: In the four-bar mechanisms, the limiting positions cannot always be avoided. Hence statement (a) is…

Q: Centre punch is a marking tool used in workshops for the purpose of making indentations on the…

A: Center punch is a point tool having a metal rod with a conical edge at its one end for creating an…

Q: The cause of an induced angle

A: Solution ;

Q: ) Down milling operation is performed for finishing cut. Select one: True False

A: Down milling is fed in the direction of the rotation

Q: 14. Which of the following procedures would be correct to mark the center of a hole location? Select…

A: The centre punch tool is a special type of punch tool used to create a shallow indentation in a…

Q: From the following Identify cutting tool that has the cutting edge in the form of small tip made of…

A: Let us discuss about about given single point cutting tool

Q: The appropriate diameter is mm.

A: To find  diameter

Q: The following tool is used on the lathe machine to perform step turning operation. Select one: True…

A: A high-speed steel cutting tool is used to perform the operation of step turning operation in a…

Q: minimum value for the thickness of the plates

A: Given; What should be the minimum value for the thickness of the plates to guard against tensile…

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.