Hello. We designed and built 4-bit adder using a GAL 22V10 device. We programmed the GAL22V10 chip and verified the operation of the circuits, the last part was this: Determine the largest adder that will fit into a GAL22V10 device. Omit the overflow detection circuit. How we could do this part? Thank

Hello. We designed and built 4-bit adder using a GAL 22V10 device. We programmed the GAL22V10 chip and verified the operation of the circuits, the last part was this: Determine the largest adder that will fit into a GAL22V10 device. Omit the overflow detection circuit. How we could do this part? Thank

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

A certain packaged IC chip can dissipate 5W. Supposewe have a CMOSIC design that must fit on onechip and requires 10 million logic gates. What is theaverage power that can be dissipated by each logicgate on the chip? If the average gate must switch at100 MHz, what is the maximum capacitive load ona gate for VDD =3.3 V, 2.5 V and 1.8 V.
Implement a 1-bit full adder circuit by using 4x1 MULTIPLEXER and an INVERTER. Data inputs are A, B, Cin and name the outputs as Sum, Cout.
Q1: Design a combinational circuit with four inputs lines that represent a decimal digit in BCD and four output lines that generate the 9’s complement of the input digit. Q: 2 Show how a full adder can be converted to full-subtractor with the addition of one inverter circuit.
Illustrate a 2 bit binary parallel adder (it is a digital circuit that produces arithmetic sum of two binary numbers in parallel) also mark which transistors are “ON” and “OFF” if inputs are 10 and 01 using Emitter-coupled logic (ECL)
Draw the schematic for a four-input NOR gate witha saturated load device. What are the W/L ratios ofall the transistors, based on the reference inverter ? (b) What is VL if all the logic inputs are equal to 1?
design 2 to 8 bit binary comparator and write it's summary?
S Display will be designed for a thermometer. The display will show that degree for minimum temperature and 99 degrees for maximum temperature. According to this; a) What is the number of bits that will be needed in the binary code to express the temperature? b) What are the binary, octal and hexadecimal equivalents of 95 degrees? () What is the BCD representation of 95 degrees? d) What is the hex equivalent of this temperature when it shows 111 degrees octal? e) If the thermometer showed a temperature between -99 and +99 degrees, how many bits would we need?
Q1. Refer to the truth table in Table Q(a) Find the Boolean expression for function Z(b) Using not more than 10 transistors, draw the gate-level and transistor-level schematics for the Boolean function.
Assume Vth = 1V and k = 50mA/V2. Given the schematic below, do the following: 1) Indicate and verify the state of each MOSFET and ?0 for the following input combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use ?ds,on approximation for linear operation. 2) Determine what kind of logic circuit is implemented in the circuit.
write a verilog code and testbench for 4-bit ripple carry adder using data flow modelling
Assume that you need 0.6 V across RE to properlystabilize the current in the modified ECL gateas shown. Design the resistors in the gate fora logic swing of 0.4 V and an average current of1 mA through RB and RE . What are the minimumvalues of VEE and the value of VREF?
Q: Show, how to use the ROM circuits to multiply two binary numbers each of two bits.(DSD)