Hi, I am having trouble understanding this scenario and any help would be very appreciated. :) I have three bars of 6061 aluminium alloy and I want to two graphs showing all of their performances. The three bars have the data as follows; Bar 1: Cross Sectional Area = 10 mm2 Length = 40 cm Bar 2: Cross Sectional Area = 20 mm2 Length = 40 cm Bar 3: Cross Sectional Area = 10 mm2 Length = 70 cm (a) how would I make a graph showing the three bars' structural performance in tension? (b) how would I make a graph showing the three bars' performance in tension till their yield? Any help would really be appreciated thank you!

Hi, I am having trouble understanding this scenario and any help would be very appreciated. :) I have three bars of 6061 aluminium alloy and I want to two graphs showing all of their performances. The three bars have the data as follows; Bar 1: Cross Sectional Area = 10 mm2 Length = 40 cm Bar 2: Cross Sectional Area = 20 mm2 Length = 40 cm Bar 3: Cross Sectional Area = 10 mm2 Length = 70 cm (a) how would I make a graph showing the three bars' structural performance in tension? (b) how would I make a graph showing the three bars' performance in tension till their yield? Any help would really be appreciated thank you!

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter17: Engineering Materials

Section: Chapter Questions

Problem 29P

See similar textbooks

Similar questions

According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 412 mm2, 601 mm2 , and 260 mm2 respectively.Determine the change in length (in mm) of the bar if P = 30280 N.The moduli of elasticity are 81.17 GPa for bronze ,71.07 GPafor aluminum , and 202.36 GPa for steel . Round off the final answer to four decimal places.
Consider a 1 m-long bar of 2024-T81 aluminum alloy with a 20mm-diameter and the following property data: E=70GPa Y.S.=410MPa T.S.=480MPa %Elongation at failure=8% What will be the length of the bar under a structural load of 1.2×10^5N in tension? Your answer should be in units of meters (m).
A rod made of aluminum alloy with a gauge length of 200 mm, diameter of 11mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.10 mm and the diameter was changed to 9.9967mm, calculate the modulus of elasticity and Poison’s ratio. Are the numbers in line with standard numbers for Aluminum Alloy?
If an aluminum weighs 165 lb/ft^3, How much will a 12-in dia. sphere weigh when immersed in oil of SG = 0.75
A cylindrical rod 600 mm long and having a diameter 13.2 mm is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 1.4 mm when the applied load is 30 KN. Which of the four metals or alloys listed below are possible candidates. Justify the answer with calculations Material modulus of elasticity(gpa) yield strength(mpa) tensile strength(mpa) Aluminium alloy 70 255 420 Brass alloy 100 345 420 Copper 110 210 275 Steel alloy 207 450 550
1. Find the center of gravity for the system shown in figure 1. 2 Calculate the moment of inertia of each body about its center of mass (about z axis). 3. Calculate the moment of inertia of the system about point A (about z axis) which is shown in figure 1. Note 1: The material used in this system is AISI 1023 carbon steel, and all dimensions is in inch. Note 2: symbol X in the dimension shown in figure 1 is the average =2+5+1/3=2.6 I think it's complicated; try your best expert.
Please answer ASAP! STRENGTH OF MATERIALS (Please write the complete solutions and FBD/Free-Body Diagram legibly. No long explanation needed. Rate/Thumbs up will be given. Answer in 3 Decimal Places)
Consider the 1040 carbon steel listed in the textbook's Table 6.1: A 20mm-diameter bar of this alloy is used as a structural member in an engineering design. The unstressed length of the bar is precisely 1m. The structural load on the bar is 1.2×10^5N in tension. What will be the length of the bar under this structural load (in meters)? Values from table: E [GPa (psi)] = 200(29*10^6) Y.S [MPa (ksi)] = 600(87) T.S [MPa (ksi)] = 750(109) Percent Elongation at failure = 17
A steel plate (called a cover plate) having cross-sectional dimensions W2 5.0 in. x 0.4 in. is welded along the full length of the bottom flange of a W, 12.0 in. x 87.0 in. wide-flange beam (see the figure, which shows the beam cross section). I W2 cover plate What is the percent increase in the smaller section modulus (as compared to the wide-flange beam alone)? Round your answer to two decimal places. % in smaller section modulus =
A homogenous steel rod has a diameter of 1.5 inches. When a load is applied, it deformed to about 0.045 inches. If the length of the rod is 6 ft and the modulus of elasticity is E=29x10^6 psi. Determine the force applied in kilopounds (kips).
5. A rigid steel container is partially filled with a liquid at 15 atm. The volume of the liquid is 1.23200 L. A a pressure of 30 atm, the volume of the liquid is 1.23100 L. Find the average bulk modulus of elasticity of the liquid over the given range of pressure if the temperature after compression is allowed to return to its initial value. What is the coefficient of compressibility? (3 DECIMAL IN FINAL ANSWER PLS!!)