An alloy has a yield strength of 41 ksi, a tensile strength of 57 ksi, and an elastic modulus of 16 * 106psi. A cylindrical specimen of this alloy 0.5 in. in diameter and 10 in. long is stressed in tension and found to elongate 0.3 in.On the basis of the information given, is it possible to compute the magnitude of the load that is necessary to produce this change in length? If so, calculatethe load. If not, explain why.

An alloy has a yield strength of 41 ksi, a tensile strength of 57 ksi, and an elastic modulus of 16 * 106psi. A cylindrical specimen of this alloy 0.5 in. in diameter and 10 in. long is stressed in tension and found to elongate 0.3 in.On the basis of the information given, is it possible to compute the magnitude of the load that is necessary to produce this change in length? If so, calculatethe load. If not, explain why.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter17: Engineering Materials

Section: Chapter Questions

Problem 27P

See similar textbooks

Similar questions

A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa,and an elastic modulus of 105 GPa. A cylindrical specimen of this alloy 12.7 mm in diameter and 250 mm long is stressed in tension and found to elongate 7.6 mm. On the basis of the information given, is it possible to compute the magnitude of the load that is necessary to produce this change in length? If so, calculate the load. If not, explain why.
A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa,and an elastic modulus of 105 GPa. A cylindrical specimen of this alloy12.7 mm in diameter and 250 mm long is stressed in tension and found to elongate 7.6 mm. On the basis of the information given, is it possible to com-pute the magnitude of the load that is necessary to produce this change in length? If so, calculate the load. If not, explain why.
Question 1: A 25mm diameter aluminum rod is loaded axially in tension with a load of 100kN. The rod is 4 m in length. Aluminum has a modulus of elasticity of 69GPa and a Poisson’s ratio of 0.35. 1) What is the decrease in diameter of the rod due to the applied load? 2) What is the new length of the rod?
A rod made of aluminum alloy with a gauge length of 200 mm, diameter of 11mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.10 mm and the diameter was changed to 9.9967mm, calculate the modulus of elasticity and Poison’s ratio. Are the numbers in line with standard numbers for Aluminum Alloy?
In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. Determine the modulus of elasticity for this material: ____x106 lb/in2. Pay attention to units and calculate your answer to 1 decimal place for the unit specified above.
Only attempt if you know the correct answer with all steps. A cube made of an alloy with dimensions of 2 in. X 2 in. X 2 in. is placed into a pressure chamber and subjected to a pressure of 15 ksi. If the modulus of elasticity of the alloy is 29000 ksi and Poisson's ratio is 0.30, what will be the length of each side of the cube, assuming that the material remains within the elastic region?
A specimen is originally 300 mm long, has a diameter of 12 mm, and is subjected to a force of 2.4 kN. When the force is increased from 2.4 kN to 9 kN, the specimen elongates 0.250 mm. Determine the modulus of elasticity for the material if it remains linear elastic. Express your answer to three significant figures and include the appropriate units.
A specimen is originally 300mm long, has a diameter of 14mm, and is subjected to a force of 2 kN. When the force is increased from 2 kN to 8 kN, the specimen elongates 0.225 mm. Determine the modulus of elasticity for the material if it remains linear elastic. Express your answer to three significant figures and include the appropriate units.
A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile load. The rod must not experience plastic deformation or an increase in length of more than 0.9 mm when a load of 24.5 kN is applied. Which of the four materials listed in Table are possible candidates? Justify your answer.
A cylindrical rod with a radius of 0.3 in. and a length of 15 in. is subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.018 in. when the applied load is 7,000 lb, which of the four metals or alloys listed below are possible candidates? Justify your choice(s).
Consider a 1 m-long bar of 2024-T81 aluminum alloy with a 20mm-diameter and the following property data: E=70GPa Y.S.=410MPa T.S.=480MPa %Elongation at failure=8% What will be the length of the bar under a structural load of 1.2×10^5N in tension? Your answer should be in units of meters (m).
Given that a steel cylinder of dimensions 12.0 mm in diameter and 70 mm long is subjected totension.(a) Determine the modulus of elasticity in the figure below.(b) Using the figure below, calculate the deformation in the steel cylinder subjected to 15 kNtension force.