How to perform zero point reset

Q: 05, 0.05, 0.06, 0. t number of reac

A:

Q: Which option is used to obtain * ?properties palette in Autocad Left click on the figure From modify…

A:

Q: Give two reasons for using standard letter designations

A: There are standard abbreviations called as letter designations used for showing various welding…

Q: Statics; working

A:

Q: Position and Disnlacanant Analveis

A:

Q: the open circuit voltage and

A: Given; In a DC are welding operation, the voltage-arc length characteristics was obtained as,…

Q: True or False: Polar tracking can be set to detect any angle

A: To display the alignment paths defined by the polar angles, polar tracking can be used. In 3D-views,…

Q: For a given frame size, a three phase machines gives a higher output than a single phase machine.…

A: The correct answer is true.

Q: ley is a uniform disk (Idisk= the cord unwinds, the acceler

A: given:mass=1.1kgmass of pulley M=3kgR=20cm

Q: the following is not one of the nonmachine tool applications of numerical control.   Question 24…

A: None of the above is the correct answer

Q: A major disadvantage of on/off control is that it cannot work for applications requiring very small…

A: On-off controller (also called two-step controller) turns on or off the machine based on the error…

Q: In a tap set, the plug tap is the final one and is also known as taper tap. Select one: True False

A: Plug Tap

Q: Any open loop systems with pre-set timer may be called as a smart system Select one: O True O False

A: any loop system with preset timer may be called as open loop system.

Q: In the drilling process shown in Figure 1, there are which cylinders A and B are used to clamp the…

A:

Q: What is the difference between Momentary Contact and Maintained Contact?

A: Maintained Contact means that when you push it on it stays on until you push it off and so on.

Q: Choose one of the following stuations to explain how impulse relates to it.

A:

Q: 5) Front panel port and interface naming/indication is denoted Above the port/interface Below the…

A: 5. In the desktop computers, a front panel port is widely used to connect various devices like the…

Q: the speed can be positive or negative false true

A: Speed is a scalar quantity. it has no direction so, speed can be positive or zero. it cannot be…

Q: What is statically balance forces

A:

Q: er notation from the options provided. [Select] ed to be on top of each number. [Select] J Nim -IN…

A:

Q: What happen when input II (push button) is pressed. 11 Q1 () Q1 Q2 O a. Ql -1 Q2 0 Ob.Ql-1Q2 1 Oc.…

A: The correct answer for the above mentioned question is given below. I am pretty sure of the answer.

Q: A fixed rating pressure switch is adjusted inside the pressure control and display console to record…

A: Fixed rating pressure switch cannot be adjusted inside the pressure control because due to fixed…

Q: Name three types of automatic controls.

A: Given Data : Automatic controls

Q: Which of the following settings does not allow you to control point specifications?a. Grid b. Snap…

A: From the given options, the snap, ortho and the polar settings are used to specify a point. Hence…

Q: Compare any two speed control circuits with neat circuit diagram. (Meter in, out or bleed off)

A:

Q: torque to rotate disk underwater

A: Torque, also known as the moment of a force, is the propensity of a force to spin the body to…

Q: Basically a NC machine runs on a program fed to it through Punched tapes Select one: True False

A:

Q: explain the Frank-Read source multiplication mechanism

A: The frank read source is a mechanism based on dislocation multiplicationin a slip plane under shear…

Q: 4. Describe two type of starting system principles and draw the basic starting circuit

A: The starting system is a combination of mechanical and electrical parts that work together to start…

Q: ---- is used to give the counter turning cycle of CNC machine. a. G96 b. G00 C. G01 O d. G73

A: G00- Rapid positioning  G01- Linear interpolation

Q: a-) What is konck? Describe the Knock mechanism formed in the cylinder by drawing a figure. What is…

A: Knocking is the phenomena commonly occurring in a CI engine. You may know that in a CI engine the…

Q: step of construction with sutible dimmenstion

A: To show the step of construction with sutible dimmenstion

Q: Q1.With a neat diagram ,explain about the working of Flash Type  ADC

A: Flash Type ADC is based on the principle of comparing analog input voltage with a set of…

Q: 4. Describe the sequence of events that occur as the manually operated directional control valve in…

A: 4.     A sequence valve is a pressure valve that opens when the predetermined pressure is…

Q: 7.How many fully rotating revolutes in a crank rocker mechanism? A 3 в 1 с 4 D 2

A: Above given mechanism is the one of the inversion of four link mechanism.  Here, slider is fixed.

Q: Which command is not modal?

A: All are modal for G code.

Q: The piston rod of a double-acting cylinder is to advance when a 3/2- way push button valve is…

A: As for controlling the speed in pneumatic cylinder which is using the proportion air FA series.…

Q: The memory unit of PLC is used to write the program to control output device. Select one: True…

A: The memory unit of PLC is used to write the program to control output device. Select one: True…

Q: In four bar mechanism, the angle between Limiting position of output link is called O None O…

A: The kinematic chain is the number of links joined together to have relative motion with each other.…

Q: Bending Tool Problem: Sheet metal is to be bended on a pneumatically actuated bending rig. After it…

A:

Q: In the following crank-rocker mechanism, #117, and #2-25. What is its time ratio? B₂ 04 OA 1.15…

A: Given: ϕ1=17°ϕ2=28°

Q: Modified True or False. Dial indicators do not convert rotational to linear displacements using a…

A: Dial indicator is a measurement device used to convert linear displacement to rotation on circular…

Q: Based on the timing diagram below, choose the correct statement regarding Timer Relay. On Coil Power…

A: option C is the correct answer

Q: Bohar model Gizmo answer keys

A: Niels Bohr proposed in 1913 that the unique spectral lines produced by various elements were related…

Q: How to draw front view and top view of the following componen

A: Orthographic Projection is a technique for drawing a three-dimensional object from various angles.…

Q: Explain the Interruption Cycle with neat sketch

A: The Interruption cycle (also known as the fetch–decode–execute cycle) is the cycle that the…

Q: 3. Describe with a neat sketch the method of operation of rope brake dynamometer.

A:

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.