Compare any two speed control circuits with neat circuit diagram. (Meter in, out or bleed off)

Q: Which of following system is not an open loop control system? O a. Air conditioner O b. Automatic…

A: Open loop control system is a type of system in which feedback is not provided to regulate the…

Q: Make a circuit for representing starting system of vehicle.

A: The starting system is one of the engine's systems, which provides an engine start. To make it, the…

Q: 1. Explain the following with neat sketch. i)vane type actuators. ii)piston type actuators

A: i) Vane type actuators Vane-type rotary actuators are shown in simplified cutaway views in figure…

Q: Explain the type of PLC, how it operates, the benefits and justification for using PLC within a…

A: Programmable Logic Controller is known as PLC. It is an industrial computer used in many…

Q: While discussing secondary voltage: Technician A says that the normal required secondary voltage is…

A: Solution:

Q: a) Explain the two different ways for port mapping (i.e. connecting signals in module instances). b)…

A: Port forwarding, also known as port mapping, is a type of network address translation (NAT) that…

Q: A) Using electro-pneumatic  control method Draw the circuit of operation  (the pneumatic circuit and…

A: electro-pneumatic  control method Draw the circuit of operation  (the pneumatic circuit and…

Q: Enumerate at least 10 applications of instrumentation for better output.

A: Instrumentation: It is a branch of science which deals with the automated measurement and its…

Q: Draw and Explain the Circuit diagram for holding the cylinder of double acting cylinder in the fully…

A: Solution: C = Double acting cylinder  P = Pump E = Electric Motor  T = Tank  F = Filter  R = Relief…

Q: Label the various pneumatic components of the circuit below

A: In this problem, it is saying to label various pneumatic components of the circuit.

Q: 3. Discuss the advantages and disadvantages of hydraulic control system with respect to pneumatics…

A:

Q: What is the difference between Momentary Contact and Maintained Contact?

A: Maintained Contact means that when you push it on it stays on until you push it off and so on.

Q: 2. Discuss the advantages and disadvantages of hydraulic control system with respect to pneumatics…

A:

Q: Explain  what is follower mechanism.

A:

Q: Describe the working of a hydraulic circuit which is used for sudden need of power source in the…

A: Hydraulic Circuit.

Q: ons: In what situations would a circuit with multiple system pressu Are there any disadvantages to a…

A: 3. Hydraulic pressure is expressed as a force per unit of area, such as bar (kg/cm2) or PSI…

Q: 4.(a) fixed displacement motor (b) Hydraulic operated check valve (c) Directional control valve for…

A:

Q: a. Explain resonant earthing system with diagram b. How will you give Combined Leakage and Overload…

A: (a) Resonant earthing system : Resonant earthing is a sure uncommon sort of high impedance earthing…

Q: ystem.

A: given: Explain overdamped, critically damped and underdamped system.

Q: Meter-out of pneumatic circuits utilizes check valve in only single direction. Select one: O True O…

A: We have to determine true/false

Q: Based on the hydraulic circuit in Figure 4, (a) Explain how the system works?

A: Given Hydraulic circuit consist of  1. Reservoir  2. Filter 3. Pump 4. Pressure relief valve 5. 4/3…

Q: Draw the Circuit diagram for holding the cylinder of double acting cylinder in the fully extended…

A: Directional control valves follow or perform only three functions: 1) Stop Fluid Flow 2) Change the…

Q: e natural frequency of the system ?

A: Given: A mass,m=3 kgIt is attached to two identical,springs each of stiffness,k=35 kN/mNatural…

Q: 3/ Design the hydraulic circuit for any one hydraulic system application with working and neat…

A:

Q: Explain the use and importance of system strategy and look-up tables in the computerized control…

A: Computerized control system:-  A computerized control system is a type of computer system that…

Q: What is the difference between a pilotduty and a line break overload?

A: When there is too much current passes through the electrical devices then in that case overload…

Q: The by pass control circuit is otherwise called as

A: The by pass control circuit is otherwise called as bleed of circuit. This type of flow control…

Q: Examine the circuit in Figure 18-12. A. Describe the sequence of events that occur as the…

A: Given : To find: What happens when directional control valve changes its position

Q: The symbol used for normally close contacts in PLC is, O a. O b. Oc. O d. HE

A: we are to select the symbol for NC PLC

Q: . Ward Leonard method is ___________ a) Armature control method b) Field control method c)…

A: This method is used for controlling the speed of DC motor.it is the basic armature control method.

Q: What is an attenuator used for?

A:

Q: ....... is an example of Secondary sensing element

A: A secondary sensing element converts the signals from one form to electrical signals. The output of…

Q: Identify the equipment where Gyro-compass heading input is supplied.

A:

Q: The value of Vg-Vf at critical point is * O infinity two

A: Pure substance is the substance that can exists with same chemical composition in all the phases it…

Q: 1. A mixing vat has an inlet valve, an outlet valve, a mixing motor, and a single level detecting…

A: Given : To find : PLC diagram

Q: A shunt generator is running at 1000 rpm. If flux is reduced by half, then what is * ?the new speed…

A: In shunt generator the flux is directly proportional to the speed.

Q: Problem: Boxes (or certain production parts) are moved by a double-ac cylinder away from a…

A: This  problem is solved using Pneuma solver software.

Q: Explain briefly, Meter out and bleed off circuits with neat circuit diagram.

A: Given: Explain briefly, meter out and bleed off circuit with neat sketch diagram.

Q: Q1 What are the main parts of dc machines and explain the function of each part

A:

Q: Controllers can be divided into _____________   type, and _____________    type controllers due to…

A: Given question: Controllers can be divided into _____________   type, and _____________    type…

Q: ...... is an example of Primary Sensing Element

A: Primary sensing element-  The element which recived the energy from the measured medium and then…

Q: Home Work: develop a sketch to controlling a servo Motor using a single push bottom as:

A: if else statement to control the servo motor according to the condition. Arduino Uno continuously…

Q: What are the types for pressure-releasing circuits? Please explain their differences.

A: The Pressure releasing circuits uses pressure control valves for keeping the system pressure below a…

Q: frequency of the system.

A: GIVEN; Mass of two identical springs is;  m=12 kgEach of stiffness,k=50 kN/m=50×103 N/mIt is under…

Q: Discuss the implementation of a split range control in boilers with a necessary diagram.

A: Spilt Range Control: Spilt control device is used to control the two final elements with a single…

Designing techniques

Engineering design is described as a method that engineers use to identify and solve a problem by taking a fixed series of steps. The engineering design process involves designing a component or machine element that satisfies certain criteria or performs a specific function. This includes designing, building, and testing the product or machine element.