If a G =77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member,Determine the maximum shear stress in shaft 1.Select the correct response:495.751 MPa278.009 MPa200.167 MPa595.095 MPa An aluminum tube of outer diameter R2 = 50 mm is heated such that it is mounted over a steel shaft of radius, R = 20 mm as shown in the figure The length I of the member is 3 m.MTRRiIf a G, = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member,Determine the maximum shear stress in shaft 1.777

Answered: Image /qna-images/answer/ebccecbb-e02c-47d2-85dd-cc551ce18a86.jpg

If a G1=77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in shaft 1. Select the correct response: 495.751 MPa 278.009 MPa 200.167 MPa 595.095 MPa

If a G1=77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in shaft 1. Select the correct response: 495.751 MPa 278.009 MPa 200.167 MPa 595.095 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.5P: A tubular bar with outside diameterd2= 4.0 in, is twisted by torques T = 70,0 kip-in. (see figure)....

See similar textbooks

Similar questions

-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A thin-walled circular tube and a solid circular bar of the same material (see figure) are subjected to torsion. The tube and bar have the same cross-sectional area and the same length. What is the ratio of the strain energy U1in the tube to the strain energy U2in the solid bar if the maximum shear stresses are the same in both cases? (For the tube, use the approximate theory for thin-walled bars.)
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
A tubular bar with outside diameterd2= 4.0 in, is twisted by torques T = 70,0 kip-in. (see figure). Under the action of these torques, the maximum tensile stress in the bar is found to be 6400 psi. Determine the inside diameter rtf of the bar. If the bar has length L = 48.0 in. and is made of aluminum with shear modulus G = 4,0 × 106 psi, what is the angle of twist d (in degrees) between the ends of the bar? (c) Determine the maximum shear strain y (in radians)?
A solid aluminum bar (G = 27 GPa ) of diameter d = 40 mm is subjected to torques T = 300 N - m acting in the directions shown in the figure, Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
A solid circular bar of steel (G = 78 GPa) transmits a torque T = 360 N - m. The allowable stresses in tension, compression, and shear arc 90 MPa, 70 MPa, and 40 MPa, respectively. Also, the allowable tensile strain is 220 x 10-6, Determine the minimum required diameter d of the bar, If the bar diameter d = 40 mm, what is Tmax?
A tapered bar AB with a solid circular cross section is twisted by torques T = 36,000 lb-in. (sec figure). The diameter of the bar varies linearly from dAat the left-hand end to dBat the right-hand end. The bar has length L = 4,0 ft and is made of an aluminum alloy having shear modulus of elasticity G = 3.9 × 106 psi. The allowable shear stress in the bar is 15,000 psi and the allowable angle of twist is 3.0°. If the diameter at end B is 1.5 times the diameter at end A, what is the minimum required diameter dAat end A?
Two circular aluminum pipes of equal length L = 24 in. arc loaded by torsional moments T (sec figure). Pipe I has outside and inside diameters d2= 3 in. and L2, = 2.5 in., respectively. Pipe 2 has a constant outer diameter of d2along its entire length L and an inner diameter of d1but has an increased inner diameter of d3= 2.65 in. over the middle third. Assume that E = 10,400 ksi, u = 0.33, and allowable shear stress ra= 6500 psi. Find the maximum acceptable torques that can be applied to Pipe 1; repeat for Pipe 2. If the maximum twist e of Pipe 2 cannot exceed 5/4 of that of Pipe 1, what is the maximum acceptable length of the middle segment? Assume both pipes have total length L and the same applied torque T. Find the new value of inner diameter d3of Pipe 2 if the maximum torque carried by Pipe 2 is to be 7/8 of that for Pipe L If the maximum normal strain in each pipe is known to bemax = 811 x 10-6, what is the applied torque on each pipe? Also, what is the maximum twist of each pipe? Use the original properties and dimensions.
A uniformly tapered lube AB of circular cross section and length L is shown in the figure. The average diameters at the ends are dAand d£= 2d t. Assume E is constant. Find the elongation S of the tube when it is subjected to loads P acting at the ends. Use the following numerical data:^ = 35 mm, L = WO mm, E = 2.1 GPa. and P = 25 tN. Consider the following cases. (a) A hole of constant diameter dAis drilled from B toward A to form a hollow section of length x - U2. (b) A hole of variable diameter a\.x) is drilled, from B toward A to form a hollow section of length x = L/2 and constant thickness t = dA/20.
-22 Two tubes (AB, BC) of the same material arc connected by three pins (pin diameter = d ) just left of B as shown in the figure. Properties and dimensions for each tube are given in the figure. Torque 2ris applied at x = 2L/5 and uniformly distributed torque intensity tQ= 37/L is applied on tube BC. (a) Find the maximum value of load variable T(N m) based on allowable shear (tx) and bearing(cha ) stresses in the three pins which connect the two tubes at B. Use the following numerical properties: L = 1.5m, E = 74GPa, v = 0.33, dp= 18mm, ta=45MPa, =90 MPa, di=85 mm, di = T$ mm, and d3— 60 mm. (b) What is the maximum shear stress in the tubes for the applied torque in part (a)?