If the average dc load voltage for a resistance of 986.3 Q in a half- wave rectifier is 56.6 V. What is the required a.c. voltage if the diode has a resistance of 32.3 Q. a. 184.34 O b. 59.15 O c. None O d. 178.51 O e. 182.94

If the average dc load voltage for a resistance of 986.3 Q in a half- wave rectifier is 56.6 V. What is the required a.c. voltage if the diode has a resistance of 32.3 Q. a. 184.34 O b. 59.15 O c. None O d. 178.51 O e. 182.94

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Related questions

Q: A full-wave bridge rectifier with a 236.86V p-p sinusoidal input has a load resister of2KΩ i. Draw…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: Q5: Design a full-wave rectifier with 1kN load. The rectifier operates from A.C supply of 220v and…

A: The full wave rectifier with the given specifications can be made as: The RMS voltage at the…

Q: An FWR using a centre-tapped Transformer Supplies an average voltage of 120V to a 250 kΩ load…

A: A)Average output voltage of FWR is =2Vmπ=120 VVm=120×π2Vm=188.5 V

Q: 7 Full-Wave Rectification 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a…

A: In this question full wave bridge rectifier is given...We have to find dc voltage at load ,PIV of…

Q: 1- The process of adding an impurity to an intrinsic semiconductor is called. 2- The maximum number…

A: According to the bartleby's guidelines we have to solve only first three subparts of a question so…

Q: A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate…

A: The Given full wave rectifier, The Values are VODC=7.5, P0=20mW, Vmp=311.13Vpf=60Hz,…

Q: The full-wave rectiﬁer ias shown is operating at a frequency of 60 Hz, and the rms value of the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Consider the circuit given in Figure (Q4). Let VD = 0.8 V and R = 100 N, find: a) The value of C…

A: Given Diode voltage VD=0.8 V Frequency f=60 Hz Resistance R=100 Ω RMS voltage Vrms=12 V Ripple…

Q: A half-wave recitifier is connected to a 50V AC source. If the load resistance is 100 ohms, find:

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 kN. a.…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: O A full-wave bridge rectifier with 120-Vrms Sinusoidal input has a load resister of Iks. a) if…

A: The solution can be achieved as follows.

Q: (a) Determine the minimum and maximum input voltages that can maintain the zener diode IN4753A in…

A: To solve above question, one should know about Zener diode and its application. A Zener diode is a…

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 kN. a.…

A: As per the guidelines of Bartley we supposed to answer first three subpart only

Q: 6. Describe the chaxacterr'stecs of the ideal diode and how they O determine the on and off states…

Q: Q3: A full-wave bridge rectifier with a 100V ms sinusoidal input has a load resistor of 1 k. a. If…

A: Solve for the peak value of the input voltage. Vm=2Vrms=2100 V=141.42 V

Q: 1.68 A half-wave rectifier circuit with a 500-2 load oper- tes from a 120-V (rms) 60-Hz household…

A: We need to calculate peak voltage and average output voltage and average output current for half…

Q: 2. A full-wave bridge type rectifier with a 120 Vrms sinusoidal input has a load resistor of 1 kN.…

A: We need to find dc voltage and PIV .

Q: In a fully controlled rectifier with RL load and freewheeling diode. Which of the given condition is…

A: Fully controlled rectifier with RL. Load The period of the free wheeling diode?

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 kN. a.…

A: In this question, We need to determine the dc average voltage Vdc? , PIV, maximum current rating…

Q: 2. A full-wave bridge type rectifier with a 120 Vrms sinusoidal input has a load resistor of 1 kN.…

A: The solution is given below

Q: If a diode full wave rectifier circuit is excited by an ac source with an amplitude of 10 V and…

A: For a full wave rectifier circuit using diodes, if VP is the amplitude of the ac signal voltage…

Q: Q2/ Determine the minimum input voltage required for regulation to be established in the figure.…

A: Whenever zener diode is in breakdown at the time output voltage will be constant that is equal to…

Q: Define the main difference between a rectifier diode and a Zener diode? What is their difference in…

A: To describe the difference between rectifier diode and zener diode along with their difference in…

Q: 1. Describe what will happen to the output voltage and PIV of a center-tapped full wave rectifier if…

A: Solution-1) In the centered tapped full-wave rectifier, mainly two diodes are used. This two…

Q: A three-phase, half-wave uncontrolled rectifier is fed from an ideal three-phase voltage 50 Hz. The…

A: According to the question we have to calculate, (a) The average output voltage and average load…

Q: A power supply of bridge rectifier system with 1-kQ load and 10 pF capactor value, is supplied by…

A: The circuit can be made as:

Q: Give a design for a pn diode voltage reference source that outputs 5 volts DC from a 12-volt source.…

A: Stack of 7 diodes: If V0 is 5V and all diodes are equal, then the voltage drop on the diodes will…

Q: A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 kN. a. If…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: A full-wave bridge rectifier with a 12V (pk) sinusoidal input has a load resistor of 20 k. (a) If…

A: given that Peak voltage Vm= 12 VRMS Voltage VRMS =122 = 8.48V (a) now…

Q: ww

A: Since the diode voltage is given as 0.6 V, the full-wave rectifier is shifted by 1.2 V. The voltage…

Q: Consider that the output voltage of a half wave rectifier with resistive load is 30V. If we replace…

A: Hello. Since your question has multiple parts, we will solve first question for you. If you want…

Q: 4.69 A full-wave rectifier circuit with a 500-2 load operates from a 120-V (rms) 60-Hz household…

Q: A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 k_. (a) If…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: 4.71 A full-wave rectifier circuit with a 1-k2 load operates from a 120-V (rms) 60-Hz household…

Q: Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical…

A: Introduction: Bridge rectifier is full wave rectifier circuit, converts AC in DC. Transformer steps…

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of I kn. a.…

A: In this question, We need to determine the dc voltage at the load? PIV, maximum current through…

Q: A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate…

Q: 5. A single-phase diode bridge rectifier is supplying a load of 100 2. A capacitor needs to be…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Derive the average and rms output voltages and currents for three-phase half controlled rectifier…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: A full-wave bridge rectifier with a 100V rms sinusoidal input has a load resistor of 1 k. a. If…

A: Given that, Vs=100 V RL=1 kΩ= 1000 ohm we have to find a. Vdc b. PIV…

Q: A rectifier circuit is used to charge a 12 Vdc battery using a 40 Vpp AC source, according to the…

A: The Given is to design rectifier circuit. In the Given rectifier circuit charge a V0=12 Vdc battery…

Q: 4.68 A half-wave rectifier circuit with a 1-k2 load oper- ates from a 120-V (rms) 60-Hz household…

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 kſN. a.…

A: As per the guidelines of Bartley we supposed to answer first three subpart only for solution of…

Q: Find the average and rms values of the sinusoidal voltage measured at the output of full-wave…

A: Given: Full wave rectifier output To do: we have to compute the average and rms values of the…

Q: Determine the dynamic AC resistance of the diode characteristics with a 2mA of current using the…

Q: Determine the ripple factor for the filtered rectifier circuit below when RL= 4KQ. Then explain…

A: Solution : The peak to peak variation of the output of a rectifier is called as ripple factor.…

Q: Design a full wave bridge rectifier power supply to deliver an average voltage of 20 V with a…

A: Given Data: Average output = 20 V Peak to peak ripple voltage = 0.1 V Average load current = 15 mA…

Q: Q4. In the full-wave diode rectifier shown below, the diodes are ideal. The source voltage is v, =…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of I kfn. a.…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Concept explainers

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).

Question

If the average dc load voltage for a resistance of 986.3 in a half-
wave rectifier is 56.6 V. What is the required a.c. voltage if the diode
has a resistance of 32.3 Q.
O a. 184.34
O b. 59.15
O c. None
O d. 178.51
e. 182.94

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Concept

VIEW

Step 2: Solution

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A full-wave bridge rectifier with a 236.86V p-p sinusoidal input has a load resister of 2KΩi. Draw the wave form that the load resistor R would see. ii. Assuming diodes are ideal, what is the dc voltage available at the load resistor? iii. What is the dc voltage available at the load if silicon diodes are employed? iv. Calculate the maximum current flow through the Diode D4 during conduction.
1N4001, 1N4002, 1N4003, 1N4004, 1N4005, 1N4006 and 1N4007 For any of the diodes, describe with the aid of diagrams/illustrations its applications in an AC to DC Bridge rectifier power supply circuit. For your circuit show and describe how you are going to smooth out the ripple voltage that will be present.
In a center-tapped full wave rectifier circuit utilizing ideal diodes, if the primary voltage is 160Vpeak, the turns ratio is 8:1 and the load resistance is 860 ohms, what is the rectified dc voltage at the output? express answer in volts
A full-wave bridge rectifier with a 12V (pk) sinusoidal input has a load resistor of 20 k. (a) If silicon diodes are employed, what is the dc voltage available at the load? (b) Determine the required PIV rating of each diode. (c) Find the maximum current through each diode during conduction. (d) What is the required power rating of each diode?
3.4 PRE-LABORATORY QUESTIONS 1. What is a rectifier? 2. How does a diode act as a rectifier? 3. What is the significance of PIV? What is the condition imposed on PIV? 4. What is meant by regulation? 5. What is meant by time constant? 6. What is meant by ripple factor?
The half-wave rectiﬁer as shown is operating at a frequency of 60Hz, and the rms value of the transformer output voltage vI is 12.6V±10%. What are the nominal and worst case values of the dc output voltage VO if the diode voltage drop is 1V?
(a)Derive the average and rms output voltages and currents for three-phase half controlled rectifier with free wheeling diode and RLE load.(b))In a single phase full converter, if output voltage has peak and average values of 325V and 133V respectively, find the firing angle.
a) Find the value of DC voltage of the RL load resistance.b) Find the required rated PIV values for each diodes.c) Find the maximum conduction current of the diodes.d) Plot waveforms of the output current and voltage values.
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary.
Sketch current I vs, voltage V for the circuits below. The breakdown voltage of the Zener diodes are shown. Assume 0.6V for all diodes (including Zener diodes) in the forward bias region.
Figure shows an AC source G having an effective voltage of 240 V, 60 Hz is connected to a single-phase full-wave rectifier. The resistance for R is 53 Ω and ripple-to-ripple current is 15%.Determine the DC voltage and DC current across the resistor. Hence, determine the power absorbed by the load. Assuming all diodes are ideal.
Consider the circuit.a. What type of circuit is this?b. What is the total peak secondary voltage?c. Find the peak voltage across each half of the secondary.d. Sketch the voltage waveform across RL.e. What is the peak current through each diode?f. What is the PIV for each diode?