If the base plate carries a load of XX kN (including self-weight, which is equally distributed on the four corners), calculate the stress on the lower washers before the nuts are tightened. Analyse the stress in the upper and lower washers, when the nuts are tightened so as to produce a tension of YY kN on each bolt. Please refer appendix for XX and YY values. Xx=145kN Уу350kN 44 mm- Upper washer Base plate Lower washer - 20 mm 22 mm 50 mm

If the base plate carries a load of XX kN (including self-weight, which is equally distributed on the four corners), calculate the stress on the lower washers before the nuts are tightened. Analyse the stress in the upper and lower washers, when the nuts are tightened so as to produce a tension of YY kN on each bolt. Please refer appendix for XX and YY values. Xx=145kN Уу350kN 44 mm- Upper washer Base plate Lower washer - 20 mm 22 mm 50 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.5P: The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw...

See similar textbooks

Similar questions

The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
a b 5.6 ft 7.6 ft Problem Statement:The truss shown is loaded with a force of F=5.6kip at an angle of θ=10∘. Determine the forces carried in members AM, DE, and IJ. (Denote tensile forces with positive values; compressive forces with negative values.)
The pin at O can support a maximum force of 3.5 kN. What is the corresponding maximum load L which can be applied to the angled bracket AOB? A. 0.541 kN C. 2.632 kN B. 1.676 kN D. 3.091 kN
Members AB and BC can each support a maximum compressive force of 760 lb , and members AD, DC, and BD can support a maximum tensile force of 2000 lb. a = 10 ft. (Figure 1) Determine the greatest load P the truss can support.
Given the Frictionless Frame as shown below with pin connection atPoint A and Point C.Determine the following if the uniform load is ‘w’:a.) The Internal Reaction at Point A in terms of w.b.) The External Reaction at Point B in terms of w.c.) The Internal Reaction at Point C in terms of w.d.) The External Reaction at Point D in terms of w. NOTE: 3 DECIMAL PLACES
PROBLEM: Determine the forces in each member using any methoddiscussed in your theory of structures/mechanics. Using Software is notallowed. Show complete solution and tabulate your answers indicatingwhether it is compression or tension. Use Pn = 205 kN, Po = Zero. a) From the Problem and the image , Design one tension member, use either a double angle of a wt section. Check its adequacy using 1 line of bolts (three bolts in a line spaced at 75mm on centers) Assume a bolt diameter from 16-22mm. Use A 36 for all steel. Neglect block shear.
Referring to Prob. 10.43 and using the value found for the force exerted by the hydraulic cylinder CD , determine the change in the length of CD required to raise the 10-kN load by 15 mm.Reference to Problem 10.43:
Each of the two members is made from 6061-T6 aluminum and has a square cross section 1 in. * 1 in. They are pin connected at their ends and a jack is placed between them and opened until the force it exerts on each member is50 lb. Determine the greatest force P that can be applied to the center of the top member without causing either of the two members to yield. For the analysis neglect the axial force in each member. Assume the jack is rigid.
Find the load on each bar of the cage given below. Its dimensions are base 2a and height 3a. EB passes through the midpoint of the lattice. Angle of force F1= 700 with horizontal (choose an angle between 15o and 75o)
The assembly is made of A-36 steel cylinders. (Figure 1) Part A: If the gap between C and the rigid wall at D is initially 0.15 mm, determine the magnitudes of the support reactions at A and D when the force P = 220 kN is applied. Enter your answers in kilonewtons to three significant figures separated by a comma. Fa, Fd = ?
The 65 kg tag is supported by cables AB and BC, as shown in the image, which have diameters of 1.5 mm and 2 mm, respectively. If the cables have a normal ultimate stress of ?u = 400 ???. Determine: a) The safety factor in cable AB b) The safety factor in cable BC Please add the free body diagram.