Acid/base titration of vinegar Imagine that you accidentally used 30 mL of water instead of ~20 mL to wash down your flaskin the procedure. You may assume that you documented this correctly (as 30 mL) innotebook. Will your final result (% mass of acetic acid in vinegar) be lower, the same, or higherthan if you had done the procedure correctly? Explain your answer.your

Acid-base titration of vinegar is done in laboratories to find out the concentration of acetic acid.…

Imagine that you accidentally used 30 mL of water instead of ~20 mL to wash down your flask in the procedure. You may assume that you documented this correctly (as 30 mL) in your notebook. Will your final result (% mass of acetic acid in vinegar) be lower, the same, or higher than if vou had done the procedure correctly? Explain vour answer.

Imagine that you accidentally used 30 mL of water instead of ~20 mL to wash down your flask in the procedure. You may assume that you documented this correctly (as 30 mL) in your notebook. Will your final result (% mass of acetic acid in vinegar) be lower, the same, or higher than if vou had done the procedure correctly? Explain vour answer.

Macroscale and Microscale Organic Experiments

7th Edition

ISBN:9781305577190

Author:Kenneth L. Williamson, Katherine M. Masters

Publisher:Kenneth L. Williamson, Katherine M. Masters

Chapter7: Extraction

Section: Chapter Questions

Problem 1Q

See similar textbooks

Similar questions

10g coffee 4g sodium carbonate 40m dichloromethane 160ml distilled water coffee filter What are the principles behind caffeine being extracted from coffee using the above items? 1st sodium carbonate mixed with coffee then brought to a boil for 20min then solution/grinds are filtered. Then solution is added to a separatory funnel with 15ml of dichloromethane and two layers are observed so the bottom layer with DCM contains the caffeine, then this layer is collected in a beaker and dried out using molecular seeds. Then the solvent is brought to a boil with crude caffeine remaining and recystallized using 95% ethanol and brought to a boil again. Then the contents are vaccum filtered and allowed to dry resulting in 30mg caffeine.
calculate the weight of Sodium carbonate normality 0.1 N and prepared -1 * ? with 100 ml distilled water, given that the molecular weight was 106 gm
The density of the first fraction collected would be expected to be close to a value of ______. 1.00 g./mL 0.895 g/mL 0.789 mL 0.950 g.mL
A 18 g of unknown organic sample was dissolve in 756 mL of benzene. The boiling point of benzene was increased by 3.36oC. As the first step of analysis, determine the moecular weight of the unknow sample? Kb of benzene= 2.64oC/m Bb of benzene = 80.09 oC density of benzene = 0.874 g/mL at 25 °C Answer in whole number, no units required.
Solution Calculations Using unit analysis, clearly show the set-ups for your calculations. You wish to prepare 50.0 mL of 2.30 x 10–2 M solution of Levothyroxine (hint-how many grams will you need of Levothyroxine?) 1. Describe how to prepare this solution from the pure drug and deionized water. Analytical balances and volumetric flasks are available to you. (Assume that Levothyroxine dissolves in water, at least to the extent necessary for this problem.) Use complete sentences in your description of the solution preparation process. a. A patient is given 2.0mL of a 3.00% (m/v) solution of Levothyroxine, how many milligrams of the drug did they receive? b. What is the molarity of a 3.00% (m/v) solution of Levothyroxine?
Emmett, a sophomore chemistry major, was trying to separate an unknown mixture. His instructor told him that there was a carboxylic acid, phenol, and amine present in the mixture. He dissolved 3 g of the unknown in 10 ml of t-butyl methyl ether. He then added 10 ml of 3M sodium hydroxide to the mixture. He used a separatory funnel to separate the layers and collected the aqueous layer in an Erlenmeyer flask labeled fraction 1. Then he added 10 ml of 1.5M sodium bicarbonate to the remaining ether. He separated the layers, and collected the aqueous layer in an Erlenmeyer flask labeled fraction 2. Finally he added 10 ml of 1.5 M hydrochloric acid to the ether, and separated the aqueous later in an Erlenmeyer flask labeled fraction 3. Emmett neutralized the respective fractions. He obtained precipitate in fraction 1, and fraction 3. He ran an IR of the solid obtained in fraction 1 and saw a broad absorption at 3500-3300 cm-1 and a sharp absorption at 1710 cm-1. Fraction 3 showed…
What is the concentration in units of grams of dye per liter of solution ,of the dilute dye solution that is produced as follows? transfer 19.53 ml of stick solution (6.10g/L) to a 200.0Ml volumetric flask and dilute to the 200 ml line with deionized water. Correct number of significant figs
A binary mixture of benzene and toluene containing 57.47 mol% benzene is continuously distilled. The distillate contains 90.40 mol% benzene, while the bottom product contains 86.96 mol% toluene. What molar flow rate of the bottom product will correspond to 183.11 mol/h of the distillate product? Type your answer in mol/h, 2 decimal places.
Show that mmol of aspirin recovered divided by mmol of limiting reagent x 100% gives the same % yield as calculated above
which procedure will produce 200ml of a solution that is 2.5%by volume alcohol of water?
Volume of acetic anhydride: 2.98 mL Mass of salicylic acid: 1.00 g Mass of aspirin recovered: 0.67 g Show that mmol of aspirin recovered divided by mmol of limiting reagent x 100% gives the same % yield (please explain) Thank you.
A 2.0 g of MgCO3 was dissolved and diluted to exactly 500-mL volumetric flask. If 50-mL aliquot was used in the analysis, what is the weight of MgCO3 present in the aliquot sample