In a double-pipe, counter-flow heat exchanger, water entering at 1 kg/s is heated from 23°C to 69°C as it flows thru the inner pipe. Hot oil enters the heat exchanger at 2 kg/s and 110°C. The convection heat transfer coefficients in the cold- and hot-sides are 100 and 50 kW/m².°C, respectively. Calculate the required heat transfer area in m?. Take cp = 4.18 kJ/kg.°C for water, and cp = 1.67 kJ/kg.°C for oil. Round your answer to 2 decimal places. Add your answer

In a double-pipe, counter-flow heat exchanger, water entering at 1 kg/s is heated from 23°C to 69°C as it flows thru the inner pipe. Hot oil enters the heat exchanger at 2 kg/s and 110°C. The convection heat transfer coefficients in the cold- and hot-sides are 100 and 50 kW/m².°C, respectively. Calculate the required heat transfer area in m?. Take cp = 4.18 kJ/kg.°C for water, and cp = 1.67 kJ/kg.°C for oil. Round your answer to 2 decimal places. Add your answer

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.32P

See similar textbooks

Similar questions

Water flowing in a long, aluminum lube is to be heated by air flowing perpendicular to the exterior of the tube. The ID of the tube is 1.85 cm, and its OD is 2.3 cm. The mass flow rate of the water through the tube is 0.65kg/s, and the temperature of the water in the lube averages 30C. The free-stream velocity and ambient temperature of the air are 10m/sand120C, respectively. Estimate the overall heat transfer coefficient for the heat exchanger using appropriate correlations from previous chapters. State all your assumptions.
In a double-pipe, counter-flow heat exchanger, water entering at 1.5 kg/s is heated from 25°C to 70°C as it flows thru the inner pipe. Hot oil enters the heat exchanger at 2.5 kg/s and 115°C. The convection heat transfer coefficients in the cold- and hot-sides are 100 and 50 kW/m2∙°C, respectively. Calculate the required heat transfer area in m2. Take cp = 4.18 kJ/kg∙°C for water and cp = 1.67 kJ/kg∙°C for oil.
Consider a water-to-water double-pipe heat exchanger whose flow arrangement is not known. The temperature measurements indicate that the cold water enters at 20°C and leaves at 50°C, while the hot water enters at 80°C and leaves at 45°C. Do you think this is a parallel-flow or counter-flow heat exchanger? Explain.
Answer the following questions about heat transfer in a double tube heat exchanger.(1) In a double tube heat exchanger in which hot and cold fluids flow into a countercurrent flow, the temperature of the hot fluid dropped from 60°C to 30°C, and the temperature of the cold fluid rose from 20°C to 55°C. Calculate the heat flux [kcal/m2h] when the overall heat transfer coefficient of this heat exchanger is constant at 69 kcal/m2h℃.(2) In a double tube heat exchanger in which hot and cold fluids flow in parallel flow, the temperature of the hot fluid dropped from 60°C to 45°C, and the temperature of the cold fluid rose from 20°C to 40°C. When the heat flux of this heat exchanger is 600 kcal/m2h, calculate the overall heat transfer coefficient of this heat exchanger [kcal/m2h℃].
In a countercurrent double-pipe heat exchanger, the hot oil entering the inner tube at 420 K with a flow rate of 60 g/s is required to be cooled to 320 K. In the space between the outer tube and the inner tube of the heat exchanger, cooling water flows at the same linear speed as the oil. Cooling water enters the heat exchanger at 290 K. The inner tube inner diameter of the heat exchanger is 25 mm and the outer tube inner diameter is 40 mm. Calculate the length of the heat exchanger. The oil side heat transfer coefficient is 1.6 kW/m2 K, and the water side heat transfer coefficient is 3.6 kW/m2 K. The densities of oil and water can be taken as 0.8 and 1.0 g/cm3, respectively, and the specific heats of oil and water can be taken as 2.0 and 4.2 kJ/kg K, respectively. Wall effects can be neglected. Flow cross-sectional area = (PI)*D2 /4 F2
Water (cp = 4180 J/kg·K) is to be heated by solar-heated hot air (cp = 1010 J/kg·K) in a double-pipe counter-flow heat exchanger. Air enters the heat exchanger at 102°C at a rate of 0.3 kg/s, while water enters at 25°C at a rate of 0.1 kg/s. The overall heat transfer coefficient based on the inner side of the tube is given as 80 W/m2·K. The length of the tube is 12 m and the internal diameter of the tube is 1.2 cm. Determine the outlet temperature of water. (Round the answer to a single decimal place.) The outlet temperature of water is ______ °C.
Water (cp = 4180 J/kg·K) is to be heated by solar-heated hot air (cp = 1010 J/kg·K) in a double-pipe counter-flow heat exchanger. Air enters the heat exchanger at 102°C at a rate of 0.3 kg/s, while water enters at 25°C at a rate of 0.1 kg/s. The overall heat transfer coefficient based on the inner side of the tube is given as 80 W/m2·K. The length of the tube is 12 m and the internal diameter of the tube is 1.2 cm.determine the outlet temperature of water and air.The outlet temperature of water is ____ CThe outlet temperature of air is ____C
Water (cp = 4180 J/kg·K) is to be heated by solarheated hot air (cp = 1010 J/kg·K) in a double-pipe counter- flow heat exchanger. Air enters the heat exchanger at 90°C at a rate of 0.3 kg/s, while water enters at 22°C at a rate of 0.1 kg/s. The overall heat transfer coefficient based on the inner side of the tube is given to be 80 W/m2·K. The length of the tube is 12 m and the internal diameter of the tube is 1.2 cm. Determine the outlet temperatures of the water and the air.
A double-pipe parallel-flow heat exchanger is used to heat water (cp = 4180 J/kg·K) from 25°C to 60°C at a rate of 0.2 kg/s. The heating is accomplished by geothermal water (cp = 4310 J/kg·K) available at 134°C at a mass flow rate of 0.3 kg/s. The inner tube is thin-walled and has a diameter of 0.8 cm. If the overall heat transfer coefficient of the heat exchanger is 550 W/m2·K, determine the length of the tube required to achieve the desired heating. (Round the answer to a single decimal place.) The length of the tube required to achieve the desired heating is ________ m.
Milk is flowing through a heat exchanger at a rate of 2000 kg/h. The heat exchanger supplies 111,600 kJ/h. The outlet temperature of the product is 95C. Determine the inlet temperature of the milk. The product specific heat 3.9 kJ/kg degrees C
Determine the rate of heat transfer and the heat transfer surface area on the tube side if A shell-and-tube heat exchanger with 2-shell passes and 12-tube passes is used to heat water (Cp = 4180 J/kg · °C) with ethylene glycol (Cp = 2680 J/kg · °C). Water enters the tubes at 22°C at a rate of 0.8 kg/s and leaves at 70°C. Ethylene glycol enters the shell at 110°C and leaves at 60°C. If the overall heat transfer coefficient based on the tube side is 280 W/m2 · °C,
1. A double-pipe parallel-flow heat exchanger is used to heat cold tap water with hot water. Hot water (Cp = 4.25 kJ/kg. K) Enters the tube at 85°C at a rate of 1.4 kg/s and leaves at 50 °C The heat exchanger is not well insulated, and it is estimated that 3 percent of the heat given up by the hot fluid is lost from the heat exchanger. If the overall heat transfer coefficient and the surface area of the heat exchanger are 1150 W/m2K and 4 m2, respectively, determine the rate of heat transfer to the cold water and the log mean temperature difference for this heat exchanger.