In stripping In > an-1 O True False

Q: tollowing mie by mahmg tables where possible: Oct G-2)+1)

A:

Q: niform ac

A:

Q: wharmonics a

A: ANSWER- n=3

Q: Describe How to mesh irregular volume by using ANSYS?

A: To mesh a volume with all hexahedron elements, the following conditions must be satisfied; 1.The…

Q: What are the two basic types of indicator movements?

A: Dial indication gauge is the name of the precision measurement device that uses a needle and a…

Q: work part to be an anode. F) making the wo par 14) In electrochemical machining, the electrode is…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: True or False: Polar tracking can be set to detect any angle

A: To display the alignment paths defined by the polar angles, polar tracking can be used. In 3D-views,…

Q: Iron Ore are mainly used to produce high heat in blast furnace Select one: True False CamScanner

A: Iron ore are mainly used to produce high heat in blast furnace.

Q: A major disadvantage of on/off control is that it cannot work for applications requiring very small…

A: On-off controller (also called two-step controller) turns on or off the machine based on the error…

Q: aHom a ncla with a spccd O. paads contal The distance it w

A:

Q: What is a wet mounts?

A: A procedure that is performed in a laboratory to observe motile organisms in wet mounts. It is an…

Q: What G-code designates IPM feed rate mode? IPR feed rate mode?

A: CNC machine feed rates are often specified in either inches per minute (IPM) or inches per…

Q: TRANSPOR TI

A: introduction: People's living standards rose dramatically because trading became easier, safer,…

Q: pe oriented in a n Ligh middlo

A: The mould chamber must hold its shape until the metal has cooled and solidified completely for a…

Q: 02/Explain the operation and benefits of AMT.

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: distributed loac

A:

Q: ss distribution stance. If it yiel s of the yield.

A:

Q: What is the difference between a pilotduty and a line break overload?

A: When there is too much current passes through the electrical devices then in that case overload…

Q: What are the advantages of cold-side ESPs over hot-side ESPs?

A: Electrostatic precipitators(ESP)  are devices which are used to remove dust and smoke particles from…

Q: Explain where did 23.4 came from

A: Use linear interpolation technique to calculate saturation pressure at 20 degree Celsius.

Q: is subjected to high-frequency sti ction

A: Summation can be accomplished by increasing stimulation frequency or recruiting additional muscle…

Q: uck return mechanis is 180mm. The incli

A:

Q: What is normal operating conditions?

A: Normal operating condition refers to the condition at which any machine can work without any fatigue…

Q: What does the headgear of a mine do

A: Consider the diagram shown below for the headgear mechanism.

Q: How does the fault tolerance used by SONET work?

A: Fault tolerance is a feature of operating systems that allows them to adapt to hardware or…

Q: Friction less cannot be with cutting surfaces, during ansys simulation True False

A: Friction less cannot be with cutting surfaces, during ansys simulation True False

Q: -of-the art wave harvesting devices while identifying what for boosting e and reliability.

A: Give the state-of-the art wave harvesting devices while identifying what for boosting their…

Q: What is the most common control cable used (size)?

A: generally the most commonly used are 7x7 and 7x19 cables.

Q: In Auto-CAD object snap is used to pick accurately--- of a line. End point Mid point Nearest point

A: In Auto-CAD object snap is used to pick accurately-of a line. O End point O Mid point ONearest point

Q: How to creat Drive Shaft in (Siemens) SINUMERIK

A: A drive shaft is a vehicle shaft that transmits power from the transmission to the wheels. The…

Q: hat is nameplate reading on machine? what inference can be from it

A: Name plate details. indicate the design and performance data of the machine. By using this data we…

Q: QUESTION 9 What does it mean to 'back feed' through a transformer and when would this happen at…

A: Backfeeding is the flow of electric power in the direction reverse to that of the generally…

Q: What is a coupling

A: Coupling is a commom word used in the field of mechanical engineering which means joining or…

Q: what is the reverse indicator alignment method ?

A: The reverse dial indicator method is a method to align the position of the two shafts accurately…

Q: A shunt generator is running at 1000 rpm. If flux is reduced by half, then what is * ?the new speed…

A: In shunt generator the flux is directly proportional to the speed.

Q: n rati

A: given: what is poisson ratio?

Q: 30. The methods of overhaul differ from maintenance procedure. a. True b. False

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: What does a milky coloured ATF indicate

A: ATF in cars is stand for automatic transmission fluid. When a radiator fails, then the contaminated…

Q: The correction factor should be greater than 1. True or False?

A:

Q: What i deep g a cons 80 rpm

A: Given data,Fr=2820NN=80deep groove ball bearing=6308SKF

Q: Describe the three types of safing sensors.

A: The safety sensor is in charge of preventing unintended deployment of the airbags. The front…

Q: minimal eft to ensure compre ng this pre

A: given:

Q: PW stand for power withdraw analysis. True or false?

A: PW is important data in power analysis.

Q: attachment is reguired in shaner?

A: Shaper Machine

Q: preload on screws for reused connections is lower than permanent connections Select one: O True O…

A: preload on screws for reused connections ,non-permanent connections is 75 percent of proof load.…

Q: Describe the types of Pressure and how to mesure.

A: Pressure  - Pressure is defined as the force applied perpendicular to an object per unit area.…

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.