In the figure, a 2.0 g ice flake is released from the edge of a hemispherical bowl whose radius r is 21 cm. The flake-bowl contact is frictionless. (a) What is the speed of the flake when it reaches the bottom of the bowl? (b) If we substituted a second flake with 3 times the mass, what would its speed be? (c) If, instead, we gave the flake an initial downward speed 1.9 m/s along the bowl, what would the answer be? (a) Number i (b) Number (c) Number tel DI Units Units Ice flake- Units <

In the figure, a 2.0 g ice flake is released from the edge of a hemispherical bowl whose radius r is 21 cm. The flake-bowl contact is frictionless. (a) What is the speed of the flake when it reaches the bottom of the bowl? (b) If we substituted a second flake with 3 times the mass, what would its speed be? (c) If, instead, we gave the flake an initial downward speed 1.9 m/s along the bowl, what would the answer be? (a) Number i (b) Number (c) Number tel DI Units Units Ice flake- Units <

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A windmill turns a series of slender rods fixed about one end . They are initially 2 meters long, and go at a speed of 15 revolutions per minute. I suggested making the blades 1m long to reduce the cross-sectional area of the windmill, keeping the mass the same for mechanical stress consistency. How fast are the windmill blades going now, in revolutions per minute?
A Jello desert resting on a plate is starts wiggling when it is sheared to the side 0.5 cm as is set on the table. The desert is a rectangular prism with a square face 25.0-cm on a side and a height of 12.0 cm. A quick Google search reveals that the density of Jello is 1140 kg/m3 with shear modulus of 530 N/m2. What is its rate of oscillation? If the energy of oscillation is dissipated at the rate of 5.00 x 10-5 J per second how long will the block wiggle?
This exercise is part of a series of problems aimed at modeling a situation by progressively refining our model to take into account more and more parameters. This progressive approach is very close to whatwhat do professional scientists do! contextWe want to lower a suspended load in a controlled way, so that it hits the ground with a speed whose modulus is not too great. To slow down the descent, we added a resort behind the mass (A), Lasuspended load (B) is connected by a rope passing through a pulley to another mass (A), which slides on a horizontal surface with friction.InformationThe masses of loads A and B are known.The mass of the rope itself is negligible (very small compared to the loads).The pulley has negligible mass and can rotate without friction.Load B is initially stationary and is at a known height h.The surface on which mass A is placed is horizontal.There is friction under mass A: the kinetic friction coefficient u, is known.The rope attached to mass A is perfectly…
A bullet (a a) 2 cm long is fired at 420 m/s and passes straight through a 10 cm thick wooden-board, penetrate (Cia) at 280 m's. Bullet (a) What is the average acceleration of the bullet through the board? (b) What is the total time that the bullet is in contact with the board? (c) What minimum thickness could the board have if it was supposed the bullet?
You open a restaurantand hope to entice customers byhanging out a sign (Fig. ).The uniform horizontal beam supportingthe sign is 1.50 m long, hasa mass of 16.0 kg, and is hingedto the wall. The sign itself is uniformwith a mass of 28.0 kg andoverall length of 1.20 m. The twowires supporting the sign are each32.0 cm long, are 90.0 cm apart,and are equally spaced from themiddle of the sign. The cable supportingthe beam is 2.00 m long.(a) What minimum tension mustyour cable be able to support without having your sign come crashingdown? (b) What minimum vertical force must the hinge be able to supportwithout pulling out of the wall?
Hi there, could I please have some help solving the problem below. Thank you very much in advance. Two particles collide with a normal direction defined: 0.7i+0.714j (eT=0.714i+-0.7j). The first mass has a mass of 4 kg and a velocity of 4i m/s. The second mass has a mass of 6 kg and a velocity of -2i+0j m/s. The collision has a coefficient of restitution of 0.6. 1. Determine the tangential velocity of the second particle after the impact [m/s]. 2. Determine the velocity in the normal direction of the second particle after the impact [m/s]. (eN w.r.t. the collision framework, not the kinematic reference frame system) 3. Determine the velocity in the j-direction of the second particle after the impact [m/s].
What is the equation for the time of flight of a projectile? Is this equation dimensionally homogeneous?
In 1589, the Italian scientist Galileo Galilei is said to have dropped two spheres of different masses from the Leaning Tower of Pisa to demonstrate that their time of descent was independent of their mass. His experiment is faulty because he neglected: (i) The body force due to gravity. The surface force due to pressure. The surface force due to friction. (ii) (iii) (A) (B) (C) (D) (i) and (ii) (i) and (iii) (ii) and (iii) All of the above
A thin-walled pipe, a uniform cylinder, a uniform sphere, and a bowling ball are all lined up on a ramp at an incline of 3 = 15°. All objects have the same total mass and diameter. As a reminder: Īp = mr², Ic=mr², is = ²mr², 18 = 2² -mr² 10 If all are released from rest at the same moment, after 5 seconds find the distance between... (a) The pipe and the cylinder (b) The cylinder and the sphere (c) The sphere and the bowling ball
(b) In two dimensional boundary layer, shear stress was changed linearly from the solid surface toward y-axis until it reach the value of zero at y = ở. Based on Table 2 and setting given to you; (i) Derive the equation of displacement thickness and momentum thickness using Von Karman Approximation Method ; and (ii) Determine the accuracy of this method in determining the value of displacement thickness and momentum thickness. C5 Table 2: Equation of Velocity Profile Setting Equation wU = 2y/8 - (y/S² 1
A wooden ball is tied to a string of length 56 cm and rotating in horizontal circle at a constant speed of 12 m/s. (a) How long will it take for the ball to complete 1 revolution? (b) What is the centripetal acceleration of the ball?
A ball is released from rest and rolls down an inclined plane, requiring 4.5seconds to cover a distance of 100 ft. What is the ball’s acceleration in cm persquare seconds?