Arshadadhom shubber H.W. 2: A 60-mm-wide by 8-mm-thick steel plate is connected to a gusset plate by a 20-mm-diameter pin. If a load of P = 70 kN is applied, determine the normal, shear, and bearing stresses in this connection. column pin diameter = 20 mm gusset plate steel plate 70 kN pin 60 mm 8-mm plate thickness

Arshadadhom shubber H.W. 2: A 60-mm-wide by 8-mm-thick steel plate is connected to a gusset plate by a 20-mm-diameter pin. If a load of P = 70 kN is applied, determine the normal, shear, and bearing stresses in this connection. column pin diameter = 20 mm gusset plate steel plate 70 kN pin 60 mm 8-mm plate thickness

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem No. 1 A standpipe with an inside diameter of 108 in. contains water, which has a weight density of 62.4 lb/ft3. The column of water stands 30 ft above an outlet pipe, which has an outside diameter of 6.625 in. and an inside diameter of 6.065 in. (a) Determine the longitudinal and hoop stresses in the outlet pipe at B. (b) If the maximum hoop stress in the standpipe at point A must be limited to2,500 psi, determine the minimum wall thickness that can be used for the standpipe.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E= 15,000 ksi] rods, and a solid steel [E= 30,000 ksi] rod. The bronze rods (1) each have a diameter of 0.625 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.375 in. If all bars are unstressed before the load P is applied, determine the normal stresses in the bronze and steel rods after a load of P= 14 kips is applied.
A torque of 1.4KNm and two forces of 10kN and 12kN are applied to the top of a 65mm diameter solid steel post. Determine the principal stresses and the maximum shear stress at point H and point K.
A thick cylinder internal diameter 240mm external diameter240mm internal diameter ‘D’ is subject to external pressure of 50MPa. Determinethe diameter ‘D’ if the minimum hoop stress in the cylinder is not to exceed200MPa.
Q3[A] prove that principal stresses are all REAL
1. The structure is used to support a distributed load of w = 15 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3,080 mm^2. The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C.
A 150-mm-long bronze tube, closed at its ends, is 80 mm in diameter and has a wall thickness of 3mm. it fits without clearance in an 80-mm hole in a rigid block. The tube is then subjected to an internal pressure of 4.00 MPa. Assuming v=1/3 and E= 83 GPa, determine the tangential stress in the tube.
Two forkend pieces are to be joined together by a single steel pin of 25mmdiameter and they are required to transmit 50 kN. Determine the minimum crosssectional area of material required in one branch of either fork if the stress in the forkmaterial is not to exceed 180 MN/m2. What will be the maximum shear stress in thepin?
The structure shown is made up of elements ABC, AD, BE, DF, joined by articulated connections at all nodes Determine Axial stress in elements AD and BE, considering a rectangular cross section of 40 x 60 mm and 25 x 50 mm respectively The average shear stress for each of the bolts of C and F, using a diameter of 19 mm, in simple shear Express results in kg/cm2
All members of the truss shown have a cross-sectional area of 500mm2 and all pins have a diameter of 20mm2. Determine: (a)The axial stresses in members BC and DE. (b)The shear stresses in the pin at A, assuming the pin is in double shear.
Q2. A mild steel shaft transmits 21 kW at 250 r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa.