In the Rankine cycle for a steam power plant the turbine entry and exit enthalpies are 2803 kJ/kg and 1800 kJ/kg, respectively. The enthalpies of water at pump entry and exit are 121 kJ/kg and 124 kJ/kg, respectively. The specific steam consumption (in kg/kW.h) of the cycle is.

In the Rankine cycle for a steam power plant the turbine entry and exit enthalpies are 2803 kJ/kg and 1800 kJ/kg, respectively. The enthalpies of water at pump entry and exit are 121 kJ/kg and 124 kJ/kg, respectively. The specific steam consumption (in kg/kW.h) of the cycle is.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a Rankine cycle, decreasing minimum pressure while holding all other parameters constant will allow an engineer to make the following statements Group of answer choices The quality at the turbine exit will decrease increasing liquid water content and back stage turbine damage, Turbine net work output will increase due to the reduced pressure at the exit The quality at the turbine exit will increase improving turbine reliability The average temperature at which heat is rejected will increase increasing thermal efficiency
For a Rankine cycle, increasing maximum temperature while holding all other parameters constant will allow an engineer to make the following statements Group of answer choices Quality at the turbine exit will decrease increasing liquid water content and causing turbine erosion. Quality at the turbine exit will increase and improve turbine durability. Increasing maximum temperature increases the average temperarture at which heat is added and will increase thermal efficiency Increasing maximum tempearture will decrease required mass flow rate for a specified power output.
in a rankine cycle, what is the entrance pressure of the turbine if the condenser pressure is 105 kpa and the pump work is 20 kj/kg. use density of water entering the pump, 950 kg/m^3.
Compare the thermal efficiency of a two-stage gas turbine with regeneration, reheating, and intercooling to that of a three-stage gas turbine with the same equipment when the maximum cycle temperature is 800°C.
Pump work of Rankine cycle is 15 KJ/kg. Density of water entering the pump is 958 kg/m^3. If condenser pressure is 100 kpa, what pressure at the entrance of the turbine?
If the turbine in a Rankine cycle operated with a second law efficiency less than 100%, how would the actual exiting quality compare to the ideal exiting quality?
Q2/ Actual Rankine cycle, has the following specifications: Boiler pressure is 160 bar and Turbine inlet temperature is 600 Co and Condenser pressure is 0.08 bar , Turbine efficiency is 0.9 and Pump efficiency is 0.85 and Steam mass flow rate is 130 kg/s Calculate: 1-Work net (kW). 2-heat addition (kW) 3-thermal efficiency.
In a single stage impulse turbine the isentropic enthalpy drop of 200 kJ/kg occurs in the nozzlehaving efficiency of 96% and nozzle angle of 15°. The blade velocity coefficient is 0.96 and ratio ofblade speed to steam velocity is 0.5. The steam mass flow rate is 20 kg/s and velocity of steam enteringis 50 m/s. Determine(a) the blade angles at inlet and outlet if the steam enters blades smoothly and leaves axially.(b) the blade efficiency(c) the power developed in kW(d) the axial thrust.Solve using velocity diagram please use the symbols below
Rannkin cycle 1_The value of enthalpy at point 1 is ( h1 =?) 2_ value of enthalpy at point 2 is ( h2 =?) 3_ value of enthalpy at point 3 is ( h3 =?) 4_value of enthalpy at point 4 is ( h4 =? 5_ value of steam mass flow rate in kg/s is 6_rate of heat supplied7_ power developed by Turbine (WT) in kW is : 8_ Thermal efficiency of Rankine cycle is:
Explain why a certain amount of thermal energy rejected intentionally incondensers and pumps are employed instead of compressors in steam power cycles?
A simple-cycle gas turbine plant has compressor and turbine efficiencies of 0.88 and 0.91, respectively, and a compressor pressure ratio of 15. The compressor intake air condition is 100 kPa and 15°C, and the TIT is 1150°C. The air mass flow rate is 560 kg/s. The fuel is natural gas with an LHV of 47 MJ/kg. Determine the plant net specific work, power output, fuel rate, thermal efficiency, and heat rate.
For a given actual Rankine Cycle, the actual turbine work serves as the input in determining the isentropic turbine efficiency. True or False