i) determine the rate of heat transfer into the cycle, and ii) evaluate the thermal efficiency of this system. QUESTION 3An ideal reheat Rankine cycle with water as the working fluid operates the boiler at15 MPa, the reheater at 1,200 kPa, and the condenser at 10 kPa. Figure 2 shows theschematic of the cycle in sequential order. The temperature is 550 °C at the entrance of thehigh pressure (High-P) and low pressure (Low-P) turbines. If the mass flow rate throughthe cycle is 3 kg/s. For cycle;High-PturbineLow-PturbineReheaterBoilerCondenserPumpFigure 2

Answered: Image /qna-images/answer/7df8b989-2801-49fc-9a85-529cce38c171.jpg

Answered: i) determine the rate of heat transfer…

Engineering

Mechanical Engineering

i) determine the rate of heat transfer into the cycle, and ii) evaluate the thermal efficiency of this system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An ideal reheat 210 MW Rankine cycle with water as the working fluid operates the boiler at 15 MPa, the reheater at 2 MPa, and the condenser at 10 kPa. The temperature is 500 0C at the entrance of the high-pressure and low-pressure turbines. Determine (a) the quality of the steam at the low-pressure turbine exit, (b) the thermal efficiency of this system, and (c) the rate of heat transfer in the reheater.
A simple ideal Rankine cycle with water as the working fluid operates between the pressure limits of 3 MPa in the boiler and 30 kPa in the condenser. If the quality at the exit of the turbine cannot be less than 79 percent, what is the maximum thermal efficiency this cycle can have? Use steam tables. The maximum thermal efficiency is
(Reheat and regenerative cycle)Consider an ideal reheat–regenerative Rankine cycle with one open feedwater heater. The boiler pressure is 10 MPa, the condenser pressure is 15 kPa, the reheater pressure is 1 MPa, and the feedwater pressure is 0.6 MPa.Steam enters both the high-and low-pressure turbines at500C. Show the cycle on a T-s diagram with respect to saturation lines and determine (a) the fraction of steam extracted for regeneration and (b) the thermal efficiency of the cycle.
A simple ideal Rankine cycle using water as a working fluid has a condenser temperature of 70 ° C and a boiler temperature of 250 ° C. What will be the thermal efficiency of the cycle as the steam enters the turbine as saturated steam?
Water enters the turbine of an ideal Rankine cycle as superheated vapor at 10 MPa and 600°C. If the condenser pressure is 10 kPa, Calculate the thermal efficiency of the system.
A steam power plant operates on the simple ideal Rankine cycle. The steam enters the turbine at 4 MPa and 500°C and is condensed in the condenser at a temperature of 40°C. draw and label the schematic diagram and the pV and TS planes. (a) Show the cycle on a T-s diagram. If the mass flow rate is 10 kg/s, determine (b) the thermal efficiency of the cycle (c) the net power output in kW.
In a reheat-regenerative Rankine cycle, the condenser pressure is 10 KPa. Steam enters the first turbine at 12.5 MPa and 500 oC. Steam is reheated at 3 MPa at the same temperature before entering the second turbine. For the regeneration, steam is extracted from the second turbine at 0.5 MPa to an open feedwater heater (OFWH). Draw the schematic and T-S diagrams. Label the points by setting point 1 at the condenser outlet, point 2 at the 1st pump (right after the condenser) outlet, point 3 at the OFWH outlet, point 4 at the 2nd pump outlet, point 5 at the boiler outlet, point 6 at the reheater inlet, point 7 at the reheater outlet, point 8 for the extraction of steam to OFWH and point 9 at the condenser inlet. Use 2 decimal places for the enthalpy, steam quality (%), thermal efficiency (%), and other energies. For the fraction of steam (y) and entropy (s), use 4 decimal places. For the specific volume, use 6 decimal places. USE THE STEAM TABLES FROM CENGEL'S BOOK ONLY 1.T-S Diagram 2…
In a reheat-regenerative Rankine cycle, the condenser pressure is 10 KPa. Steam enters the first turbine at 12.5 MPa and 500 oC. Steam is reheated at 3 MPa at the same temperature before entering the second turbine. For the regeneration, steam is extracted from the second turbine at 0.5 MPa to an open feedwater heater (OFWH). Draw the schematic and T-S diagrams. Label the points by setting point 1 at the condenser outlet, point 2 at the 1st pump (right after the condenser) outlet, point 3 at the OFWH outlet, point 4 at the 2nd pump outlet, point 5 at the boiler outlet, point 6 at the reheater inlet, point 7 at the reheater outlet, point 8 for the extraction of steam to OFWH and point 9 at the condenser inlet. Use 2 decimal places for the enthalpy, steam quality (%), thermal efficiency (%), and other energies. For the fraction of steam (y) and entropy (s), use 4 decimal places. For the specific volume, use 6 decimal places. IMPORTANT: USE THE STEAM TABLES FROM CENGEL'S BOOK ONLY…
A steam power plant operates on the Rankine cycle with reheat and has a net power of 120 MW. Steam enters the high pressure turbine at 9 MPa and 600 °C, and the low pressure turbine at 1 MPa and 600 °C; It leaves the condenser as a saturated liquid at a pressure of 10 kPa.a) Show the cycle in the T-s diagram including the saturated liquid and vapor curves.b) The degree of dryness of the steam at the turbine exit.c) The thermal efficiency of the cycled) Determine the mass flow rate of the steam.
Refrigerant-134a is used as the working fluid in a simple ideal Rankine cycle which operates the boiler at 2000 kPa and the condenser at 24C. The mixture at the exit of the turbine has a quality of 93 percent. Determine the turbine inlet temperature, the cycle thermal efficiency, and the back-work ratio of this cycle.
A ideal rankine power plant cycle uses ammonia as the working fluid.Saturated vapor leaves the boiler at a temperature of 85 o C. The condenser temperatureis 40 o C. Calculate the heat transfer to the boiler, the work done by the turbine, and thethermal efficiency of the cycle.
In an ideal reheat-regenerative cycle, steam enters the turbine at 4 MPaa and 400°C. After expansion to 1 MPaa steam is withdrawn and reheated to 380°C. Extractions for regenerative heating occur at 0.2 MPaa and 0.02MPaa and the condenser pressure is 0.005MPaa. Use mass flowrate of 1 kg/s.