In the system shown in figure find the ratio A1/A2 if the change in pressure at B by 0.5 psi gives 1 in displacement in the right leg while the pressure at A remains constant. Oil (SG = 0.8) Water Area = A2 Area =

In the system shown in figure find the ratio A1/A2 if the change in pressure at B by 0.5 psi gives 1 in displacement in the right leg while the pressure at A remains constant. Oil (SG = 0.8) Water Area = A2 Area =

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 24P

See similar textbooks

Related questions

Q: 14. In the figure, fluid A has a specific gravity of 0.90 and fluid B has a specific gravity of…

A: Given data Specific gravity of fluid A (GA) = 0.9 Specific gravity of fluid B (GB) = 3 Specific…

Q: Problem 2 A manometer connects an oil pipeline and a water pipeline as shown in Fig. 24. Determine…

A: the rate of increase of pressure in vertical downward direction at a point in static fluid must be…

Q: Figure shows an example of a hydraulic accumulator, which is a device for reducing pressure…

A: Considering spring is in natural state i.e. x=0 The mass of plate is negligible, the net force on it…

Q: Consider the parallel springs shown in the accompanying figure. Realizing that the deflection of…

A: Springs are elastic members which upon loading get distorted and after removal of load they regain…

Q: Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the…

Q: 1. A large tank contains a layer of oil floating on water as shown in the figure below. The flow is…

A: Given data Specific gravity of oil = 0.8 Density of water = 1000 Pa Acceleration due to gravity =…

Q: The figure below represents equilibrium. 85 N 60 N 45 100 N 30 F

Q: For the figure shown below i) Estimate the difference in pressure between pipe A and pipe B ii)…

A: Given- Pb = 200Kpa

Q: 6. Calculate the pressure increase that must be applied to water to reduce its volume by 2%.

Q: 4. In figure, fluids A and B have specific gravities of 0.75 and 1.00, respectively. If mercury is…

A: Given data : S.GA=0.75S.GB=1.00

Q: 3) The density of a liquid, p (kg/m³) is expressed as a function of h(m), distance from the liquid…

A: Density : A substance's density indicates the density of that material in a certain region. Density…

Q: Pitot tube is an instrument that is used to measure flowrate in a pipe. Figure 3 shows water flowing…

Q: In figure 6, compute the pressure difference between m and n, in pounds per square inch, when: (a)…

A: Writing pressure equation PM+γAz-γGz+γA4.6=PN

Q: Q2:- The pressure of the gas corresponding to various volumes V is measured, given by the following…

Q: 300 mm dia 1.5 kN Oil, s=0.82

A: Lets understand the concept,. 1.5kN force is applied to lift the position, so the liquid with…

Q: THE CIRCULAR TROUGH AS SHOWN IN THE FIGURE IS FILLED WITH WATER UP TO THE BRIM. USING THE THEOREM OF…

Q: V Figure 3

Q: Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the…

Q: Situation 2: As shown in the figure, two blocks are connected by a light, flexible cord passing over…

Q: Example 5 A closed tank shown in the given figure, is given an acceleration of 3.6 m/s, the…

Q: 1. A 15-lb block A rests on a 35-lb wedge B as shown in the figure. Determine the acceleration of…

A: Solution Given That Mass of Block A= 15 lb Mass of Block B= 35 lb

Q: f the pressure gage shown in the figure indicates a pressure of 6.5 x 10 N/m2 (6.5 bar) what are the…

A: Calculate the pressure at point B as follows: Starting from pressure gauge to the right side top of…

Q: Pitot tube is an instrument that is used to measure flowrate in a pipe. Figure 3 shows water flowing…

Q: THIS IS NOT GRADED. This is a 2020 Past Paper that I am working through. However I only have the…

Q: In the figure below, a fluid with a specific gravity of 0.77 is flowing. The mass flow rate is…

Q: Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the…

Q: AIR P=150mmHG WATER FLUID X SG=3.69 FLUID Y SG-4.69 FLUID Z SG=5.69

Q: As shown in the figure, water flows in the horizontal pipe. The pipe consists of two different…

A: velocity (V) : V = A1A12-A22*2gh* A1 = area at first section A2 = area at second section h* =…

Q: Three different fluids, water, oil (SG = 0.83), and unknown fluid, fill the tank and manometer tube…

Q: A pressurized tank contains water with some air above it. As shown on figure below. Multi-fluid…

Q: In the figure below, a fluid with a specific gravity of 0.77 is flowing. The mass flow rate is…

Q: Consider the geometry shown in the figure. The cube center is level with the surface of the liquid.…

A: According the given data in the questionThe density of the cube will be 733 kg/m^3Calculation is…

Q: the modulus of the pressure force on the 3-m wide gate AB and center of pressures.

A: Force=Pressure*Area

Q: For the differential manometer shown in figure below, calculate the pressure difference between…

Q: What is the absolute pressure inside the tank after it was submerged in a liquid if the volume of…

A: Given data Percentage volume change Atmospheric pressure To find Absolute pressure

Q: The tank shown contains air, oil, and water. Gage A reads 100 kPa and Gage C reads 16.872 kPa more…

Q: h₁ 3 Water process fluid h₂

Q: In figure 6, compute the pressure difference between m and n, in pounds per square inch, when: (a)…

Q: In the Figure, if the oil in region B has SG= 0.8 and the absolute pressure at point A is 1 atm,…

A: Given: The specific gravity of the oil is 0.8. The absolute pressure at point A is 1 atm. Consider…

Q: The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as…

Q: 2. What is the relationship between volume and pressure? 3. Calculate the volume if it is v1=1.5 L,…

Q: In the figure of three different fluids to each other without mixing, without statically flowing it…

Q: h, Determine the gauge pressure in the fluid at point A, using the reading provided by the attached…

A: Given data : Specific gravity (S.G1)=1.32h1=1.3 mSpecific weight of water (w)=9.79 KN/m3

Q: A cylinder of cross-sectional area 2500 mm is filled with sand of permeability 5.0 mm/s. Water is…

Q: In the figure shown, originally there is a H2=9 cm manometer reading and H1=15 cm. Atmospheric…

A: Atmospheric pressure =101.3 kPa H2=9 and H1=15 Gauge pressure at A= 15 cm Absolute pressure=…

Q: Water A H1 cm H2 cm Mercury

Q: Q4: A 7-cm diameter solid aluminum ball balance nicely when submerged in a fluid as shown in figure.…

A: Given: Dal = 7cm, S.Gal = 2.7, SGbr = 8.5

Q: In the figure, fluid 2 is carbon tetrachloride(1.589) and fluid 1 is benzene (SG = 0.877). If the…

Question

In the system shown in figure find the ratio A1/A2 if the change in pressure at B by 0.5 psi
gives 1 in displacement in the right leg while the pressure at A remains constant.
Oil
(SG = 0.8)
Water
Area = A2
Area = A1
%3D
Mercury

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pressure gauge at elevation 6.5 meters at the side of a tank containing a liquidreads 95 kpa. Another gauge at elevation 2.5 meters reads 115 kpa. Compute thespecific weight of the liquid in kn/m3 and draw the figure..
In the Figure, if the oil in region B has SG= 0.8 and the absolute pressure at point A is 1 atm, what is the absolute pressure at point B ?
The pressure read on the pressure gauge of the system in the figure is 65 kpa. Considering the data shown, determine the height difference "h" on the differential pressure gauge. Aire = air Agua = water Aceite = oil Mercurio = mercury
Panel AB is circular and retains a liquid with specific gravity of 1.6. It has a width of 4 feet perpendicular to the paper. It has a radius of 11 feet from its center as seen in the figure. If h = 5 feet, and a = 4 feet, determine the total hydrostatic force acting on panel AB in pounds. ANSWER : 14,359.153
A cylindrical tank having a diameter of 39cm and 20cm height floats in mercury in a vertical position . Its depth of immersion is 7cm. Determine the value of Mbo in cm Determine the metacentric height in cm Thank you!
6. Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer, as shown in figure. Determine the pressure difference Pfresh water- Psea water= ?(kPa) between the two pipelines. Take the density of seawater at that location to be P = 1035 kg/m³. (2 decimal)
Determine the pressure required to decrease the volume of the following fluidsby 2%:a. waterb. glycerinc. SAE motor oil
A tank is filled with glycerin (2 ft depth) and a gasoline (3 ft depth) with top of it. Determine the pressure at the bottom of the tank in terms of pressure head in feet of water. unit weight of glycerin=78.7 lb/ft³ and unit weight of gasoline=45.3 lb/ft³
6.60 Gasoline (sg = 0.67) is flowing at 0.11 m3/s in the fabricated tube shown in Fig. 6.19. If the pressure before the contraction is 415 kPa, calculate the pressure in the smaller tube.
The cylindrical tank shown has a hemispherical end cap ABC contains water as shown in the figure. Compute the resultant force of the fluid on the end cap ABC.
A monometer is first filled with water and then with mercury. The mercury end of the monometer is open to the atmosphere. Given that the density of water is 1000kg/m^3, and the density of mercury RhoHg=1.35x10^4kg/m^3. What is the hydrostatic pressure at point A? Express the answer as gauge pressure.
In the figure below, pipe A contains gasoline (S.G.=0.75), pipe B contains oil (S.G.=0.91) and the manometer fluid is mercury (S.G.=13.6). The initial differential reading is 0.30m as shown. Determine the pressure difference between A and B.