2. A 1.5 in. 6 by 19 plow steel rope is used to leave the cage of a mine hoist. The mine is 600 ft deep;the rope sheave is 12 ft in diameter, and the cage acceleration is 5 ft/s?. (a) Determine theapproximate cross-sectional area, in? (b)Find the approximate wire diameter, in (c) Calculate thebending load, Ib.Calculate the useful load, Ib. (g) What is the acceleration force due to the useful load, Ib.? (h) Whatis the acceleration force due to the rope, Ib.?(d) Find the weight of wire ropes, Ib. (e) Determine the ultimate load, Ib. (f)

Answered: Image /qna-images/answer/c551415b-ed7e-40bd-9e53-bb56b19f6e0a.jpg

Answered: in. 6 by 19 plow steel rope is usE he…

in. 6 by 19 plow steel rope is usE he rope sheave is 12 ft in diameter, approximate cross-sectional area, in (t (d) Find the weig pending load, Ib.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A skip for a mine shaft weighs 2000lb and is to lift a maximum load of 3000lb from a depth of 1000ft. The maximum speed of 20fps is attained in 5 sec. (a) What sizes of 6 x 19, IPS rope and sheave should be used for indefinite life and for N=1.3 on the basis of fatigue? (b) What is the design factor on the static basis? (c) What sizes of rope and sheave are required if the number of cycles (bending and unbending) in the desired life is 200,000? What is the corresponding static design factor? (d) What is the elongation of the rope found in (c) if the 3000lb load is added while the hoist hangs free at the bottom?(Use Faires)
The standard length of a tape is 100m having a weight of 1.2kg with the standardtemperature of 20 C and standard pull of 5.5kg. The young modulus of elasticity of thetape is 200GPa, cross sectional area is 2.8mm? and the coefficient of linear expansionis 0.0000116/°C. Determine the normal tension of the tape.
Determine the normal stress in each of the cables? (MPa) a. 85.7 b. 75.7 c. 65.7 d. 55.7 If the cables elongated by 1 mm, what is the vertical displacement of the precasat slab? (mm) a. 1.758 b. 1.658 c. 1.458 d. 1.558 What is the tensile force in each of the cables? (kN) a. 5.98 b. 4.98 c. 7.98 d. 6.98 SOLVE ALL AND WILL GET A LIKE <3 ps: unit weight of concrete is 24kn/m^3
Calculate Tension BD if P = 100 kN.
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of thewhole structure which is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
1) The crate weight W = 100 N and the coefficient of static friction at the surface is ? = 0.30. A force P is applied at an angle ? from the horizontal surface. A) Determine the value of ? to obtain the smallest possible value of P so that the crate is on the verge of moving. B) Determine the smallest value of P. C) Determine the normal reaction between the crate and the horizontal floor. Use method of joints or method of sections as much as possible
Determine the value of the uniformly distributed loadd "w". What is the numeric value of C1 ( 1st constant)? Dtermine the deflection at midspan.
Problem #3: A circular shaft, fixed to the wall, is loaded as indicated in the figure below. Using all three failure criteria (Rankine's theory, Tresca criterion, and Von Mises criterion), determine the load magnitude, R, that causes yielding at point A on the cross-section. Assume the yield strength of the material is 64 ksi. Notes: . . ● Point A is at the mid-depth of the section and on the leftmost fiber (as viewed below). At the fixed base, the shaft will be subjected to a bending moment, a torsional moment, a shear force, and a normal force. Recall for a circular cross-section; 1=d¹ and/=d. Q does not need to be provided, as you should see herein. A 3 ft R 4 in. F T 2 ft 12R X
A large sign is to be supported on two steel poles, each of which will be supported by an 18 in diameter drilled shaft. The lateral wind load acting on the sign will be 3,000 lb and distributed evenly between the two piles. The centroid of this wind load will be 30 ft above the ground surface. The soils are sandy clays with su = 2,500 lb/ft2. Using a rigid analysis, compute the required depth of embedment and the maximum moment in each drilled shaft. Use a factor of safety of 3.0.
Find P to keep the 600N roller from rolling down the rough inclined surface. *use 3 decimal places all throughout the solution.
An eccentric load is applied at a point 22 mm from the geometric axis of a 60-mm-diameter rod made of a steel for which σY = 250 MPa and E = 200 GPa. Using the allowable-stress method, determine the allowable load P. Take the effective length L = 1.4 m. (Round the final answer to one decimal place.)
A bearing pad is a device which is used to support a bridge or other heavystructure in a way that permits the load to shift slightly in a horizontal directionrelative to the ground or foundation. If a horizontal force af 528 kN is applied tothe top surface of the bearing pad, and that a = 700 mm, b = 550 mm, h = 75m and the modulus of elasticity G = 1.25 MPa. Determine the following: a. The average shear stress on the bearing pad.b. The horizontal displacemant of tne bearing pad. Note: Draw the Free Body Diagram, include the proper units and round-off the answers to 3 decimal places.