a steel rivet is subjected to a normal stress σ as shown in the figure.Determine and graph the principal stresses and the directions associated with them using the mohr's circle.determine and graph the maximum shear stressesgraph the possible failure planesfinally, what is the value of the maximum tangential stress and in what orientations does it take place?complementary data: σx = -30mpa; Txy = -90Mpa Ejercicio Propuesto Nº 02Un roblón de acero está sometido a una tensión tangencialTxy y una tensión normal ox, tal como se muestra en lafigura adjunta.> Determine y grafique mediante el círculo de Mohrlos esfuerzos principales y las direcciones asociadasa estos.Determine y grafique los esfuerzos cortantesmáximos.Grafique los posibles planos de falla.> Por último, ¿cuál es el valor de la tensión tangencialmáxima y en qué orientaciones tiene lugar?Datos complementarios: ox = -30Mpa; Txy = 90Mpa.xy

Normal stress = -30 MPa Shear Stress = 90 MPa

Answered: inally, what is the value of the…

inally, what is the value of the maximum tangential stress and in what orientations does it take place? complementary data: σx = -30mpa; Txy =

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.67P: The cable AB supports a uniformly distributed load of 12 lb/ft. Determine the angles A and B, and...

See similar textbooks

Related questions

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: The rectangular bar shown is connected to a support bracket with a 27 mm diameter pin. The width of…

Q: In the assembly of the bronze tube and steel bolt shown in the figure, the pitch of the bolt thread…

A: GIVEN DATA -

Q: Q5) Triaxial undrained test were performed on clay samples taken from clay stratum shown below, the…

A: The Answer is below

Q: The young modulus of the bar, which is made of St70 steel material shown in the figure, is 210GP..…

A: Given data as per the question Young modulus of the bar =210 Gpa cross section of the bar=500…

Q: The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of…

A: Given Data The diameter of pin is:d=24mm=24×10-3 m The width of the rectangular bar is:b=70…

Q: Washer To= 20 °C B 20 mm Bolt A 20 mm diameter steel rod is held snugly (without stress) between…

Q: A crack in the block created an angle 0=20" with the horizontal as described in the figure Using…

A: givenaxial stress σx=200kPaangle of plane θ=90-20o=70o

Q: The figure below are 2 solid cylindrical bars joined together at point B. Find the required minimum…

Q: The factor of safety for a machine element depends on the particular point selected for analysis.…

A: Given: The factor of safety is 2.5. The loads are: F = 2.65 kN, P = 10.5 kN, and T = 52 N-m The…

Q: Determine the nodal displacements and the element stresses, including principle stresses, due to the…

Q: Q1. A compound bar consists of a circular rod of steel of 25 mm diameter rigidly fixéd Into a copper…

A: The given area of the circular rod is given below.

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: As in the figure, a pressurized cylindrical container is made of 12 mm thick plate as shown in the…

Q: The figure below shows the cross section of a steel rectangular tube, of uniform thickness t= 25 mm,…

Q: Safe stress for the steel bar shown in the figure is sigma(safe)= 160 MPa. According to The greatest…

Q: An external force P =1800 Ib is applied to the frame shown below via a cable that passes over a…

A: we first have to know the forces acting on the system by drawing FBD of cable pulley system and…

Q: The factor of safety for a machine element depends on the particular point selected for analysis.…

A: Given dataTransvverse load F = 2.65kNAxial load P = 10.5kNTorque T = 52N-mFactor of safety N= 2.5…

Q: Using direct stiffness method determine the nodal displacement of stepped bar as shown in the…

Q: A thick-walled cylinder with internal and external radii 86 mm and 166 mm respectively, is subject…

A: we have to determine the radial and hoop stress

Q: A steel pipe with an outside diameter of 4.67 in. and an inside diameter of 4.25 in. supports the…

Q: 2.44 The figure shows the cross section of a circular steel tube that is filled with concrete and…

A: GivenP=200kipEst=29×106 psiEco=3.5×106 psi

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: 2. The stresses shown in the figure act at a point in a stressed body. Using the equilibrium…

Q: A central horizontal section of a hook is a symmetrical trapezium of inner width =67.5mm and of…

A: Given:Inner width,bi=67.5 mmOuter width,bo=22.5 mmP=37.5 KNInner radius,Ri=52.5 mmh=90 mmOuter…

Q: digit of your ID No., mm) and 10 mm thick (plus quarter of the last digit of your ID No., mm). It…

Q: Determine the equivalent stress state of an element oriented 30° clockwise with respect to the…

Q: The part shown is loaded at point C with 290 N in the positive x direction and at point E with 200 N…

A: .

Q: Problem C-2 [Average Normal and Average Shear Stresses] A structure is under an external loading of…

A: To normal and average stress at section aa

Q: Observe the figure below. Determine the following: a. axial stress on the shank if the load applied…

Q: In the crank arm of the figure, two loads P act as shown: one parallel to the x axis and another…

A: (a) Draw the given diagram with support reactions, Now, apply force equilibrium in x-direction,…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

Q: Problem 1: For the crank in the figure below and loaded as shown, determine the location of maximum…

Q: Determine factors of safety, based upon the distortion energy theory, for stress elements at A and B…

Q: 4. Shown below is a steel tube AB with a 1.5" outside diameter and .06" wall thickness. You may…

A: Given:do=1.5 int=0.6 indi=0.9 inF=50 lb

Q: Figure 1. The boiler has an inside diameter of 1800 mm and a wall thickness of 20 mm, and it is made…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: Determine the principle stresses and the maximum in-plane shear stress.

Q: A pressure vessel of thickness 10 mm and inner radius 220 mm is subjected to an internal pressure of…

A: Mohr's circle is a graphical representation of plane stress. In this representation, the stresses in…

Q: The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in…

A: Write the expression for the change in length. Here, P represents the load, L represents the…

Q: 5. Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in.…

A: Given Allowable stress in rod AB = 3400 psi Outer diameter = d1 Inner diameter = d1 - 0.125…

Q: A pressurized cylindrical container, as in the figure, is made of 12 mm thick plate as shown in the…

Q: The state of stress acting at a critical point on a wrench is shown in the figure. Determine the…

A: Given: The state of stress is given as Here, σx=300 MPaτxy=150 MPa

Q: 150 mm 40 mm 2.5 k B- 20 mm

Q: GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane…

Q: A hollow structural steel flexural member is subjected to loads of P = 9 kips, Q = 35 kips, and R =…

A: Given: The eccentric load given: P = 9 kips The direct load, Q = 35 kips The shear force, R = 22…

Q: Compare the torsional rigidities of the following sections: (a) a hollow tube 30 mm outside…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Consider the stress state illustrated in the figure, which involves a normal stress of 40[MPa] in…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

a steel rivet is subjected to a normal stress σ as shown in the figure.

Determine and graph the principal stresses and the directions associated with them using the mohr's circle.

determine and graph the maximum shear stresses

graph the possible failure planes

finally, what is the value of the maximum tangential stress and in what orientations does it take place?

complementary data: σx = -30mpa; Txy = -90Mpa

Ejercicio Propuesto Nº 02
Un roblón de acero está sometido a una tensión tangencial
Txy y una tensión normal ox, tal como se muestra en la
figura adjunta.
> Determine y grafique mediante el círculo de Mohr
los esfuerzos principales y las direcciones asociadas
a estos.
Determine y grafique los esfuerzos cortantes
máximos.
Grafique los posibles planos de falla.
> Por último, ¿cuál es el valor de la tensión tangencial
máxima y en qué orientaciones tiene lugar?
Datos complementarios: ox = -30Mpa; Txy = 90Mpa.
xy

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

NEED IN RUSH! A transmission tower is held in place by bolts at B, C, and D. If the force on the cable AD is 664 N, what is the angle of orientation with respect to the x-axis and y-axis of the wire in bolt D (θD.x and θD.y)? (degrees) Given: y = 20 m XB = XD = 2.4 m ; Xc = 8.3ZB = 4.2 m ; ZC = 2.3 m ; ZD = 10.2 m
A thin rod AB of length 1 = 600 mm is connected to a sliding sleeveon a pole. The rod rests on a C-shaped wheel located at a distancehorizontal a = 80 mm from the vertical axis of the post. Knowing that us = 0.25between the sleeve and the post, that the radius of the wheel is negligible, thatG= 100 N and 0 = 30°, determine the range of values of P ensuringthe balance of the assembly
he region of safety in maximum shear stress theory contains which of the given shape *
Perform the operation g(t)=2t+5f(t)= 2t+5find: (g+f)(t)
Only ansewr Question 4 Tension:A = 52.03 lb , Tension:B = 21.96 lb ,Tension:C = 38.4 lb
Solve for me. d.e.f.g.h
Determine the value of w and P such that the resultant of the system is a downward force of magnitude 1200 N acting 3.6 m to the right of A. Determine the magnitude of the uniform load w. a.252 N/m b.646.1 N/m c.387.7 N/m d.553.8 N/m
Determine force FBA FBD
Stiffness is the property that enables material to withstand high stress without great strain. it is a resistance to any sort of deformation and is a function of the modulus of elasticity, E of the material True or false
The layout shown is a representation of a machine shop. Components 1 and 2 have masses of m1=265kg and m2=220kg , respectively. Component 3 must be treated as a distributed load, which is w=175 kg/m2 , determined by the area of contact between the component and the shop floor. The dimensions shown have been measured to be a=0.600 m , b=2.00 m , c=1.60 m , d=0.650 m , e=3.10 m , and f=1.10 m . These dimensions represent the x and y components of the locations of the centers of gravity for the respective components. Component 3 has x,y cross-sectional dimensions of x3=1.30 m and y3=0.250 m . Assume the components experience uniform weight distribution in all principle directions. The dimensions a through f locate the centroid of the respective component from the y−z plane and x−z plane.(Figure 1) Part A - The x Component of the Center of Gravity of All the Components Determine the x component of the center of gravity of all the components. Express your answer to three significant…
A rigid rod resting on a fulcrum has the following 20-lb forces acting on it. A is attached 2 feet from the left of the fulcrum acting vertical upward. B is 4 feet to the left of the fulcrum, acting downward at an angle of 30° with respect to the horizontal. C is 6 feet from the left of the fulcrum, acting upward with an angle of 45° with respect to the horizontal. D is attached 2 feet at the right of the fulcrum, acting downward at an angle of 60° respect to the horizontal. Where can a 20 lb force be placed to put the system in equilibrium?PS: FREE BODY DIAGRAM AND SOLUTION
Voziček A spelje v trenutku, ko mimo njega po sosednjem tiru pripelje voziček B (vozička sta takrat vzporedna), ki vozi v isti smeri s stalno hitrostjo 0,5 m/s. Voziček A se giblje enakomerno pospešeno s pospeškom 0,2 m/s2. Po kolikšnem času in na kolikšni razdalji od začetka speljevanja voziček A dohiti voziček B (vozička sta takrat ponovno vzporedna)? Kolikšna je takrat hitrost vozička A?