Find the questionClassify A and B, thank. The beam shown is[rollermolerrollerاخترأحد الخياراتa. statically determinateb. unstablec. statically indeterminate to the second degreeand stabled. statically indeterminate to the first degree.and stable In the truss shown all the members are pinconnected at their ends, and the externalsupports are pins (hinges). The truss isاخترأحد الخياراتa. statically indeterminate tothe second degree and stableb. statically indeterminate to ..the first degree and stable.c. statically determinated. unstable

Answered: Image /qna-images/answer/83a3a48b-0904-4f61-95a1-4657605576ce.jpg

Answered: ind the question Classify A and B,…

Engineering

Civil Engineering

ind the question Classify A and B, thank.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6.D1 A large tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 13,300 N (3000 Ib). Determine the minimum required wire diameter,assuming a factor of safety of 2 and a yield strength of 860 MPa (125,000 psi) for the steel.
I need re-action of this beam. both reaction and simplfyied it
One transmission tower is being held by a three guy wires anchored by the bolts at the B, C, D. Given the tension in wire AB is 525lb, identify the components of the force exerted by the wire on the bolt at B.
A simple beam 16 ft long carries the loading shown inFigure 1.21a. Find the reactions.
Question:- A 7.5 meters long simply supported structural steel beam carries two concentrated loads P at every third points. Use A 572 Grade 65 steel with Fy=448.18 MPa. The beam is W310x23.8 section having the given properties. A=3040mm² d= 305mm tw= 5.6mm bf=101mm tf= 6.7 mm Ix= 43x10⁶ mm⁴ Iy=1.2x10⁶mm⁴ a) Calculate the allowable bending stress of the compression flange of beam 7.5 fully supported against lateral movement. b) Based from the previous question, calculate the value of concentrated load P that the beam could support safety.
The beam shown in the image attached is simply supported and subjected to the loads shown. If the reaction VA and VB are 14.67kN and 23.33kN respectivley, find the distance from the left hand support "A" to the point of contralexure.
If the restraint at the midspan of the beam is removed, how much deflection should it resist such that there will be no deflection at that point?
Replace the loading system by an equivalent resultant force and couple moment acting at point O.
Draw a shear diagram Cx = 0 Cy=30 Mc = -210 V {0<=x<8} = 0 V { 8< x <=14} = -5 (x-8)
Use VIRTUAL WORK METHOD to answer the questions below considering the truss shown in the figure. Assume A= 1200 mm2 , E = 200 GPa , and α = 12x10-6/°C. - Axial Foce Memeber on ED choices: -10.87 , -9.64 , -0.18, 16.78 , 2.1, -5.88, 11.18, 14.25 - Absolute Value of Axial Force on member AE choices: 3.265, 2.236, 7.811, 6.682, 0.741, 0.362, 1.286, 6.981 - Vertical Displacement of Joint A in mm due to external force only. choices: 0.888, -0.619, 0.621, 0.322, -0.887, -0.322, -0.887, -0.322, -0.184, 0.895
A mechanical support framing system is shown below. The framing consists of steel floor grating over steel beams and entirely supported by four tension hangers that are connected to floor framing above it. It supports light machinery with an operating weight of 4000 lbs, centrally located. (a) Determine the impact factor I from the Live Load Impact Factor, (b) Calculate the total live load acting on one hanger due to the machinery and uniform live load of 40 psf around the machine. (c) Calculate the total dead load acting on one hanger. The floor framing dead load is 25 psf. Ignore the weight of the hangers. Lateral bracing is located on all four edges of the mechanical floor framing for stability and transfer of lateral loads.
If the bucket weighs 50 lbs, determine the tensions developed in each of the wires. The angle for wire BC and DE is 30deg and a slope of 4 vertical, 3 horizontal for wire BE. Find the tension at wire Fb, tension at wire Fd, tension at wire Fc and tension at wire Fa.