It has a slender column of wide flange of ASTM A-36 of profile W 250 x 167 which will be used as a column with a length of 7 m, with recessed ends, in a industrial plant, if Opc = 380MPa, calculate: The factor of safety that should be considered. The maximum axial working load that the column will support.

It has a slender column of wide flange of ASTM A-36 of profile W 250 x 167 which will be used as a column with a length of 7 m, with recessed ends, in a industrial plant, if Opc = 380MPa, calculate: The factor of safety that should be considered. The maximum axial working load that the column will support.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.5P: A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure)....

See similar textbooks

Similar questions

A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness ßRat A. Determine the critical load Pcr for the structure.
A wide-flange steel column (E = 30 × l06 psi) of W12 × 87 shape (see figure) h as a length L = 28 ft. It is supported only at the ends and may buckle in any direction. Calculate the allowable load Pallowbased upon the critical load with a factor of safety n = 2.5. Consider the following end conditions: (a) pinned-pinned, (b) fixed-free, (c) fixed-pinned, and (d) fixed-fixed.
A W8 × 28 steel wide-flange column with pinned ends carries an axial load P. What is the maximum permissible length of the column if (a) P = 50 kips, and (b) P = 100 kips? (Assume E = 29,000 ksi and y = 36 ksi.)
A hollow, short compression member, of normalized cast steel (ASTM A27-58, 65 ksi), is to support a load of 1500 kips with a factor of safety of 8 based on the ultimate strength. Determine the outside and inside diameters if Do = 2Di
Calculate the maximum stress in the steel ring if a copper ring with a thread diameter of 2000 mm and a thickness of 20 mm and a steel ring with an inner diameter of 2000 mm and a thickness of 10 mm are interlocked and heated to 100°C. Scale= 100 GPa, Eçelik= 200 GPa, copper= 16.106/°C, steel= 12.10-6/°C a-) 20 MPa b-) 40 MPa c-) 50MPa d-) 60 MPa e-) 30 MPa
An industrial machine requires a solid, round piston connecting rod 200 mm long, between pin ends that is subjected to a maximum compression force of 80,000 N. Using a factor of safety of 2.5, what diameter is required if aluminum is used with properties Sy = 496 MPa and E = 71 GPa.
Please present FBD/s A tri mettalic bar is uniformly compressed by an axial force P=12kN applied through a rigid end plate. THe bar consists of a circular stell core sorrounded by brass and copper tubes. The steel core has a diamter 10mm, the brass trube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm. E for steel =210 GPa, E for brass = 100GPa and E for copper is 120GPa. Calculate the compressive stress of each metral due to force P.
Problem 3. A solid round bar is to be assembled into a collar by press fitting. The inside radius of the collar is R = 50 mm and the outside radius is o = 4C mm. Find the maximum allowable radial interference 3 if the assembly is to have a safety factor of 2 against yielding. Both parts are made of carbon steel having E 200 GPa and Sy = 300MPa Solve using the DET. ↑ O
The figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a separating force of 150 kN. (a) Determine kb, km, and C. (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. Use (SI) units as it applies