A circular bar is used as a column carrying a load of 8500 lb with pinned ends The length of the bar is 50 in. Use SAE 4140 OQT1000 steel and design factor of 3.0. (E for steel = 30,000 ksi) Determine the required diameter of the column D = in (Must show calculations and attach the worksheets in the last question)

A circular bar is used as a column carrying a load of 8500 lb with pinned ends The length of the bar is 50 in. Use SAE 4140 OQT1000 steel and design factor of 3.0. (E for steel = 30,000 ksi) Determine the required diameter of the column D = in (Must show calculations and attach the worksheets in the last question)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.13P: A steel pipe column with pinned ends supports an axial load P = 21 kips. The pipe has outside and...

See similar textbooks

Similar questions

A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
(a) Explain FIVE (5) factors that may influence the optimum column design under an axial compressive load. (b) A 3.6 m long pin-ended column is formed from an A-36 steel circular hollow section with an outer diameter of 75 mm. Determine the minimum thickness, t (to the nearest integer in mm) of the circular hollow section so that the column can safely support the load of 200 kN without buckling. If the outer diameter of the steel circular hollow section is reduced to 62 mm and the ends are pinned-fixed supported, analyse whether the column with the same applied load and the sectional thickness computed above will cause a buckling failure.
Which of the following is the design stress for a piston rod where the axial load is completely reversed if the surface of the rod is ground and the surface finish factor is 0.9? Assume no stress concentration. Use a factor of safety of 2 and an endurance limit of 250 MPa. The load factor for completely reversed axial load is 0.85.
An aluminum rod, made from alloy 6061-T6, is made in the form of a hollow square tube, 2.25 in outside with a wall thickness of 0.125 in. Its length is 16.0 in. It carries an axial compressive force of 12 600 lb. Compute the resulting design factor. Assume that the tube does not buckle.
A right angled bell crank lever is to be designed to raise a load of 5 kN at the short arm end. The lengths of short and long arms are 100 and 450 mm respectively. The lever and the pins are made of steel 30C8 (S = 400 N/mm2). And the factor of safety is 5.the permissible bearing pressure on the pin is 10 N/mm². The lever has a rectangular cross section and the ratio of width to thickness is 3:1. The length to diameter ratio of the fulcrum pin is 1.25:1. Calculate (i) The diameter and length of the fulcrum pin (ii) The dimensions of the cross section.
A circular bar of L 570mm length is supported freely at its two ends. It is acted upon by a central concentrated cyclic load having a minimum value of 20 kN and a maximum value of 50 kN. Take factor of safety of l.5, size effect of 0.85, and a surface finish factor of 0.9 . The material properties of bar are given as ultimatestrength of σu 625MPa, yield strength of σy 510MPa and endurance strength of σe 340MPA. Determine the diameter of bar by using Goodman's method and Soderberg method.
Select the lightest W shape that will act as a column of 7 m long with both end hinged and support an axial load of12KN with the safety factor of 2.2, assume the proportional limit for steel is 200 Mpa and E=208 Gpa
An industrial machine requires a solid, round piston connecting rod 200 mm long, between pin ends that is subjected to a maximum compression force of 80,000 N. Using a factor of safety of 2.5, what diameter is required if aluminum is used with properties Sy = 496 MPa and E = 71 GPa.
A circular bar of 500 mm length is supported freely at its nwo ends. It is acted upon by a central concentrated cyclic load having a minimum value of 20 kN and a maximum value of s0 kN. Determine the diameter of bar by taking a factor of safety of 1.5, size effect of 0.85, surface finish factor of 0.9. The material properties of bar are given by : ultimate strength of 650 MPa, yield strength of 500 MPa and endurance strength of 350 MPa
Q1-A frame shown in figure (1) is loaded by a force of (100 N), the cross section area of the base at point A is (10 mm width X 15mm thickness). What is minimum yield stress required to fabricate this frame using tresca theory and safety factor of (2).
Rigid bar ABCD is supported by a smoth pin at D and by vertical aluminum alloy [E=10,000 ksi] bars attached at joints A and C. Bar (1) was fabricated to its intended length L1=40 in. Bar (2) was intended to have a length of 60 in.; however, its actual length after fabrication was found to be L2=59.88 in. To connect it to the pin at C on the rigid bar, bar (2) will need to be manually stretched by Δ=0.12 in. After bar (2) has been stretched and connected to the pin at C, a load P=20 kips is applied to the rigid bar at B. Use the following additional properties and dimensions: A1=A2=0.75 in2, a = 36 in, b =54 in, and c = 48 in. Determin: a) The normal stresses in bars (1) and (2). b) The deflection at A of the rigid bar.
Problem 3. A solid round bar is to be assembled into a collar by press fitting. The inside radius of the collar is R = 50 mm and the outside radius is o = 4C mm. Find the maximum allowable radial interference 3 if the assembly is to have a safety factor of 2 against yielding. Both parts are made of carbon steel having E 200 GPa and Sy = 300MPa Solve using the DET. ↑ O