It is required that the drawworks input power be able to lift 600,000 Ib at a rate of 50 ft/min. There are eight working lines between the traveling block and the crown block. Three input power systems are available: 1,100, 1,400 and 1,800 hp. Considering that individual sheave efficiency is 96% and the draworks mechanical efficiency is 85%, which of the three will be the most appropriate?

It is required that the drawworks input power be able to lift 600,000 Ib at a rate of 50 ft/min. There are eight working lines between the traveling block and the crown block. Three input power systems are available: 1,100, 1,400 and 1,800 hp. Considering that individual sheave efficiency is 96% and the draworks mechanical efficiency is 85%, which of the three will be the most appropriate?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pneumatic system is producing 120lb/in^2 of gauge pressure. It has been determined that 7 lb of force is optimal to complete this task? What is the required area and diameter of the pneumatic cylinder?
Consider a screw used in translation along with a 22 mm. inside diameter and 38 mm. outside diameter collar. The screw has a mean; diameter of 18 mm. and has a single trapezoidal metric thread cut with a pitch of 4 mm. Determine the torque required to raise a load of 500 kg, if both the collar and the threads have a coefficient of friction of 0.3.
1.Using YOUR OWN values for rotor radius, lift, drag, and all necessary angles, justify if HAWT or some VAWT can be used in the design.
Power is transmitted from the 1st shaft to the 2nd shaft with a Conical Friction coupling at 950 rpm. If the taper angle is alpha 25 degrees and the average diameter is 120 mm, how much power is produced with a pressing force of 5000 N (kW)
7. A steel pulley with a mean rim radius of 120 mm is rotated at a speed of 1100 rpm. If the mass of the rim is 5 kgs, What is the centrifugal force?
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
Question No. 11: In a thrust bearing the external and internal radii of the contact surfaces are 210 mm and 160 mm respectively. The total axial load is 60 kN and coefficient of friction = 0.05. The shaft is rotating at 380 rpm. Intensity of pressure -is not to exceed 350 kN/m2. Calculate: Power lost in over-coming the friction and; Number of collars required for the thrust bearing.
Machine design A 60-hp four-cylinder internal combustion engine is used to drive a medium-shock brickmaking machine under a schedule of two shifts per day. The drive consists of two 26-in sheaves spaced about 12 ft apart, with a sheave speed of 400 rev/min. Select a Gates Rubber V-belt arrangement. Find the factor of safety, and estimate the life in passes and hours?
ANSWER ASAP The worm gear rotating at 1250 rpm drives a worm wheel and whose velocity ratio is 12 to 1. A driving motor with 12 hp is used to supply the worm with worm pitch gear diameter of 3.5 in. Find the tangential force on the gear.
A 30 KN of force at one end just supports a weight of 30,000 KN load at the other end. If the rope is run three times around a circular post, what is the coefficient of friction between the rope and the post?
How did you get the summation of forces in each direction?
A winch drum of diameter 161 mm turning at 12pm lifts a load of 7.5kN. What is the winch output power?